Sears CO1ZARD10UOO-4370537 - Manual (Page 17)

Review this chart to find do-it-yourself solutions for minor performance problems. Any ser­
vice needed, other than those described in this owner's manual, should be performed by
an authorized service representative.
A
IN C3 Electrical Shock Hazard
II ICr Wl, IWdI ftilvfwld 9dl V iWrli 1^ VI viddllfli|j| %ilv Uilllc
Failure to do so could result in eiectrica! shock or personal Injury.
PROBLEM POSSIBLE CAUSE POSSIBLE SOLUTION
Cleaner won't start 1. Unplugged at wall outlel
2. Tripped circuit breaker/blown fuse
at household service panel,
3. Loose hose electrical connections.
4. Tripped overload proledor in
POWER-MATE"'“
1- Plug In firmly, push OWOFF switch to ON
2, Reset circuit breaker or replace fuse
3, Reconnect hose ends, (page 7),
4, Clean brush and brush supports,
then reset, (pages 14,15).
Poor job of dirt
pick-up. Í. Full or clogged dust bag
2. Clogged airflow passages
3. Dirty motor safely liller-
4. Wrong pile height setting
5. Орал suction control
6. Hole in hose
7. Worn POWER-MATE™ brushes.
8. Worn or broken belt
9. Oifly brush or brush supports.
10, Canister hood open.
1. Change bag, (page 12)
2. Clear airflow passages, (page 12)
3. Clean filter, (page 13),
4. Adjust setting, (page B)
5. Adjust control, (page 11)
S. Replace hose
7. Change brushes, (page 16).
8 & 9. See BELT CHANGING AND BRUSH
CLEANING, (pages 14,15).
10. CiosB and latch hood
Cleaner starts but
cuts off. 1. Hose or hood electrical EOfinedions.
2 Tripped overload protector in
POWER-MATE™
3, Tripped overload protector
iti canister
1. Check conriedtons, reconnect hose
ends, (page 7)
2. Remove any Items that may be caught
or jammEd, then reset if cleaner starts
and stops again, clean brush and brush
supports, then reset, (pages 14,15),
3. Change dust bag, clear airflow blockage,
(page 12) Wail 20 minutes for motor
to cool and automatically reset.
POWER-MATE™ will not
luti WMiiflr II
k U«
■j POWER-MATE'“ connections
unplugged
2. Worn or broken belt
3. Dirty brush or brush supports
4. Tripped overload protector in
POWER-MATE™
1. Plug in firmiy, (page 6).
2 & 3 See BELT CHANGING AND BRUSH
CLEANING, (pages 14,15)
4. Check brush area for excessive lint
buiid-up or lamming Clean brush and
brush supports, then reset, (pages 14,15)
PerfarmancB indicator,
Some modeis, is red. 1, Pulì Of dogged dust bag
2, Dirty fllisr
3, Clogged airflow passage
4, Cerlam attachment tools
1. Change bag, (page 12).
2. Change filler, (page 13)
3. Clear clog from airflow passage, (page 12)
4. This is norma! Light should go off
when tool Is removed-
Cleaner picks up moveable
rugs -or- POWER-MATE™
pushes too bard 1, Wrong pile height setting
2- Suction too strong.
1. Adjust setting, (page 9),
2. Open suction control, (page 11)
Light won't work. 1. Burned out light bulb 1. Change light bulb, (page 14)
Cord won't rewind. 1, Dirty power cord
2. Cord jammed
1. Clean the power cord,
2 Pull out cord and rewind.
on carpet.
1. Wrong vacuuming pattern. 1. Sea VACUUMING TIPS, (page 9)
17