Cooper Lighting Round Tapered Aluminum RTA6L20AAS24V - Manual

COOPER LIGHTING ADH061623
S Y ST EM S
C
E R T I F I E
D
COOPER LIGHTING
Catalog #
Type
Date
Project
Comments
Prepared by
SPECIFICATION FEATURES
RTA ROUND TAPERED ALUMINUM
2 0 ' - 4 0 ' M o u n t i n g H e i g h t
[ W I T H R O U N D T W I N E L L I P T I C A L A R M ]
1 . . . Cast aluminum alloy shoe base with aluminum
alloy bolt covers or base cover dependent upon
base type.
2 . . . Flush handhole assembly with internal reinforcing
frame. 3" x 5" for 6" shafts. 4" x 6" for 7", 8", & 10"
shafts. Ground lug located opposite handhole
opening drilled & tapped for 3/8" 16NC-2 grounding
screw.
3 . . . Tapered aluminum lighting shaft with polished
finish.
4 . . . Aluminum alloy arm mounting plate fastened by
(4) 1/2" stainless steel hex head bolts, nuts and
washers. Shaft drilled 1 1/4" diameter wire hole
with 1" I.D. rubber grommet installed.
5 . . . Tapered elliptical bracket aluminum alloy satin etch
finish.
6 . . . Removable aluminum alloy pole cap secured with
(3) 1/4" stainless steel allen head cup point set
screws.
7 . . . Anchor bolt per ASTM A576 with (1) nut, (1) flat
washer, and (2) shims. Nuts, washers and threaded
portion of bolt are hot dip galvanized.
FINISH COLORS [See ordering information. Other finish colors available]
WARNING: THE USE OF UNAUTHORIZED ACCESSORIES SUCH AS BANNERS, SIGNS OR PENNANTS FOR WHICH THE POLE WAS NOT DESIGNED FOR VOIDS THE
COOPER LIGHTING WARRANTY AND MAY RESULT IN POLE FAILURE CAUSING SERIOUS INJURY OR PROPERTY DAMAGE. COOPER LIGHTING'S POLE
WARRANTY IS ALSO VOIDED IF LUMINAIRE IS NOT INSTALLED AT TIME OF POLE INSTALLATION.
B=Clear Anodized
C=Clear Bronze Anodized
D=Black Anodized E=Medium Bronze Anodized
F=Dark Bronze Powder Coat
V=Grey Powder Coat W=White Powder Coat
X=None (Natural Aluminum)
Y=Black Powder Coat
F O U R B O LT A N C H O R A G E
BC=Bolt Circle
BP=Bolt Projection
AB=Anchor Bolt
D=Bolt Diameter
H=Bolt Dimensions
EP A + MOUNTING CONFIGURA TIONS POLE COMPATIBILITY MATRIX
PRODUCT TENON Single 2 @ 180° 3 @ 120° 4 @ 90°
CONCOURSE III [CAL] 1 1/2” to 2 3/8” O.D. 1.1 2.2 3.1 3.55
LANDUA [LND] 2 3/8” O.D. 2.7 5.4 8.5 9.75
HAMMER [HR] 2 3/8” O.D. 2.11 4.22 5.8 6.59
RY COBRAHEAD 1” or 2” NPS ARM 0.87 -- -- --
RS COBRAHEAD 1” or 2” NPS ARM 0.85 -- -- --
RL COBRAHEAD 1” or 2” NPS ARM 0.51 -- -- --
RC COBRAHEAD 1” or 2” NPS ARM 0.8 -- -- --
MC/MX 2” NPS ARM 1.46 -- -- --
18"
handhole
Base View
AL
(arm length)
MH
(mounting
height)
!"
"0
"#
(
$
5
1
2
3
4
5
6