StarTech.com SLIDESHELFD - Manual (Page 2)

FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s)
to which this manual applies by the third-party company in question. Regardless of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby acknowledges that all
trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access
our comprehensive selection of online tools, documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a one year warranty.
In addition, StarTech.com warrants its products against defects in materials and workmanship for the periods noted, following the initial date of purchase. During this period, the products may be returned
for repair, or replacement with equivalent products at our discretion. The warranty covers parts and labor costs only. StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental,
consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not allow
the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.
3. Attach the front rack mounting bracket to the sliding rail. The
front bracket is the short bracket. Two screws will fasten the
bracket to the rail. Make sure the screw is inserted from inside the
rails, so the nuts and washers are on the outside.
4. The rear rack mounting bracket can be fastened to the rails in the
same manner as the front. These should not be fully tightened
however, so they can be adjusted to the exact length needed to fit
the rack/cabinet.
5. Fasten the completed rails into the cabinet/rack using the
appropriate hardware for your cabinet/rack. Make sure to fully
tighten the rear bracket to the rails, if they were left loose from
the previous step.
6. The revolving front handle can be inserted into the opening on the
front of the shelf and fastened from the rear/inside with two screws.
7. Slide the shelf onto the rails from the front and push the shelf all
the way to the back until it stops.
8. Pull the shelf out and ensure that it stops and locks when fully extended.
9. If the shelf needs to be removed (i.e. to be flipped over), refer to Step 1.
Specifications
Description
22in Deep Sliding Server Rack
Cabinet Shelf
Material Aluminum
Color Black
Maximum Weight Capacity 25 kg
Min/Max Mounting Depth 20in / 24in
Mounting Height 1U
Dimensions (WxD) 444.5mm x 559.0mm
Net Weight 5680 g
Certifications RoHS