Perfect Aire 1PAMSH36-14.5 Installation Manual - Manual

There should not be any heat source or stream
near the unit.
There should not be any obstacles blocking the
air circulation.
A place where air circulation in the room is good.
Place where drainage can be easily done.
Place where noise prevention is taken into
consideration.
Do not install the unit near the doorway.
Ensure the spaces indicated by arrows from the
wall, ceiling, fence or other obstacles.
There should not be any direct sunlight. If unavoidable,
sunlight prevention should be taken into consideration.
1. Fit the installation plate horizontally
on structural parts of the wall with
spaces around the installation plate.
2. If the wall is made of brick, concrete
or the like, drill eight (8) 0.2 inch (5mm) diameter
holes in the wall. Insert Clip anchor for
appropriate mounting screws.
3. Fit the installation plate on the wall
with eight (8) type "A" screws.
Fit the Installation Plate and drill
holes in the wall according to the
wall structure and corresponding
mounting points on the installation
plate. The installation plate provided
with the machine differs from appliance
to appliance.
(Dimensions are in "inches" unless
otherwise stated).
1. Determine hole positions according to left and right
side of the installation plate.The hole center is obtained
by measuring the distance as shown in the diagram above.
2. Dirll the piping plate hole with 2.5 inch (65mm) hole-core drill.
3. Drill the piping hole at either the right or the left and the
hole should be slightly slanted to the outdoor side.
1. For the le ft-hand and right-hand piping,
remove the pipe cover fro m the side p anel.
2. For the re ar-right-hand and rear-left-hand
piping, install the piping as shown.
3. Bundle the tubing, connecting cable, and
drain hose with tape securely, evenly as
shown in Figure on the right.
Because the condensed water from rear
of the indoor unit is gathered in the drain
pan and is piped out of room do not put
anything else in the drain pan.
1. Run the drain hos e sloping down ward.
Do not instal l the drain hose as illu strated
in Figures.
2. When conne cting extensio n drain hose,
insulate th e connecting pa rt of extension
drain hose w ith a shield pipe, do no t let
the drain hos e slack.
Connect the indoor unit first, then the
outdoor unit.
Be careful no t to let the drain ho se slack.
Heat insulated both of the auxiliary piping.
Be sure that the drain hose is located at
the lowest side of the bundle. Locating at
the upper sid e can cause dr ain pan to
overflow in side the unit.
Never intercross nor intertwist the power
wire with any other wiring.
Run the drain hose sloped downward to
drain out the condensed water smoothly.
Outdoor unit dimension
inch(L1xHxW1) L2(inch) W2(inch)
24.6 14.4
23.3 13.1
Mounting dimensions
39 x 38 x 13.6
35.3 x 33.9 x 12.5
INSTALLATION MANUAL FOR ROOM AIR CONDITIONER
(Split Wall-Mounted Type)
SELECT THE BEST LOCATION
Indoor unit
DRILL A HOLE IN THE WALL
Outdoor unit
Settlement of outdoor unit
2
CONNECTIVE PIPE AND DRAINAGE INSTALLATION
3
NOTE:
NOTE:
Fitthe InstallationPlate
Connective pipe installation
Drainage
CAUTION
Outdoor unit installation
1
The mounting wall is strong and solid
enough to prevent it from the vibration.
If an awning is built over the unit to prevent
direct sunlight or rain, be careful that heat
radiation from the condenser is not obstructed.
There should not be any animal or plant which
could be affected by hot air discharged.
Keep the spaces indicated by arrow from wall
ceiling, fence or other obstacles.
Do not place any obstacles which may cause
a short circuit of the discharged air.
I
N
D
O
O
R
U
N
I
T
4.8in. or more
from the wall
4.8in.(120mm) or
more from the wall
1
2
3
4
5
7
8
9
6
Installation Plate
Clip Anchor
Self-Tapping Screw A ST3.9x25
Seal (For cooling & heating models only)
Drain Joint (For cooling & heating models only)
Connecting
pipe
Assembly
Liquid side
Gas side
Remote Control
Self-Tapping Screw B ST2.9x10
1/4 (6.35mm)
3/8
(9.52mm)
1/2 (12.7mm)
3/8 (9.52mm)
5/8 (16mm)
Parts you must purchase. The pipe
size differs from appliance to appliance.
Consult the technician for the proper
size.
1
5-8 (depending on models)
5-8 (depending on models)
1
1
1
2
1
Except the above parts provided, the other parts needed during installation you must
purchase.
Remote Control holder
ACCESSORIES
Number Name of Accessories Qty
NOTE :
optional
parts
The seriousness is classified by the following indications.
SAFETY PRECAUTIONS
Please read this installation manual completely before installing the product.
Installation work must be performed in accordance with the national wiring standards by authorized
personnel only.
Contact an authorized service technician for repair, maintenance or installation of this unit.
This appliance is not intended for use by persons (including children) with reduced physical, sensory
or mental capabilities, or lack of experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
The design and specifications are subject to change without prior notice for product improvement.
Consult with the sales agency or manufacturer for details.
All the pictures in the instructions are for explanation purposes only. The actual shape should prevail.
1.
8
Pipe hole
6in.(150mm) or more
from the ceiling
Model A
Model B
12.8in.
1.
8
2.6 2.6
49.2in.
5.1in. 5.9in.
Hooked Part Hooker Part
Pipe hole Indoor unit outline
Correct orientation
of Installation Plate
2020331A2045
6in(15cm) or more
4.8in(12cm)
or more
4.8i
n (12cm
)
or m
ore 7.55ft(2.3m)or more
23
.7
in
(60c
m
)
or
mo
re
11.9in
(30c
m) or more
11.
9in (3
0cm)
or mo
re
23.7in
(60cm
)
6.57ft(
2.0m)
or m
ore
"
57.1in.
40.3 in. 7.5 in.
16.8 in. 16.6in
2.76in. 2.76in. 2.8in.
2.
2
1in.
1.3 in. 1.3 in.
1.4
3. 7
12.5 in. 12.5 in.
6.
9in
.
0.
8
13
.4
in
.
0.2-0.3in.
(
)
or mo
re
This symbol indicates the possibility of death or serious injury.
This symbol indicates the possibility of injury or damage to property. CAUTION
WARNING
CAUTION
WARNING
1) Install according to these installation instructions. If installation is defective, it will cause water
leakage, electrical shock, or fire.
2) It will cause the unit to fall, have water leakage, give an electrical shock and/or cause a fire.
3) Install the indoor unit per these instructions. Make sure it is secured properly to the wall. If not
installed properly the unit could drop or fall causing injury.
4) An independent circuit breaker must be used for each indoor unit. If the circuit breaker is not sized
properly, it will cause an electrical shock and/or a fire.
5) Use the specified cable and connect properly to the terminals. If the cable is not connected
properly, it will cause a hot spot or fire at the connection.
6)
Wiring routing must be properly arranged so that control board cover is fixed properly. If control board
cover is not fixed properly, it will overheat at connection point of terminal, fire or electrical shock.
7) When connecting the refrigerant piping, make sure no debris or foreign matter gets into the
refrigerant piping.
1) This equipment must be grounded properly. Follow the local and national codes when choosing the
proper outdoor electrical disconnect. The unit will not run properly and could cause an electrical
shock if not installed properly.
2) Do not install the unit at place where leakage of flammable gas may occur. In case gas leaks and
accumulates at surrounding of the unit, it may cause fire.
3) Install condensate drain pipe as mentioned in the installation instructions. If drain is not installed
properly, water could back up in the system causing water damage.
The outdoor unit should be installed on a concrete or
plastic pad or mounted to a wall with the proper brackets
and secured per local and national codes.
Both the liquid and suction refrigerant lines
must be insulated.
1. Install the outdoor unit on concrete or plastic
pad or mount to a wall with the proper brackets
and secure per local and national codes. Make
sure the unit is level.
2. Make sure the unit has 12 inches of clearance on
the back, 12 inches on the left side (as you face
the unit), 24 inches on the right side and 6-1/2 feet
in the front.
3. Install the outdoor unit in a location where the
noise and vibration level with not be an issue.
4. Select a place so the warm air and noise from
the outdoor unit does not disturb neighbors.
Indoor unit installation
1. Pass the piping through the hole in the wall.
2. Hook the indoor unit onto the upper portion of installation
plate (engage the indoor unit with the upper edge of
the installation plate). Ensure the hooks are properly
seated on the installation plate by moving it in left
and right.
3. Piping connections can be easily made by lifting the indoor unit with a cushioning material between
the indoor unit and the wall. Remove after finished piping.
4. Press the lower left and right side of the unit against the installation plate until hooks engage with the
slots.