Philips TS2745C - Manual (Page 2)

H ooking U p Y our TV (A ntenna /C able TV C onnections )
W j C able tv
C aiìu ; I nj ’ i )/C() nm ; ki i ; i {
y our Cable TV input
into your home may be
a single (75 ohm) cable, or
a Converter Box installa­
tion. In either case the
connection to the TV is
very easy. Just put the
threaded end of the cable
signal to the TV's antenna
plug and screw it down
tight.
(BEeiN)—--------------------------------
r If your Cable TV sig­
nal is a single round cable (75
ohm) then you're ready to con­
nect to the TV.
If you have a Cable TV
Converter Box:
Connect the Cable TV signal to
the Cable Signal IN(put) plug
on the Converter.
Connect the Cable TV
cable to the ANTENNA/CABLE
plug on the TV.
If you have a Cable TV
Converter Box:
Connect the OUT(put) plug
from the Converter to the
ANTENNA/CABLE plug on the
TV. ^
NOTE: The connecting cable for
the Converter is supplied from
the Cable TV Company.
Back of TV
Cable TV Converter
Box Connection
Remember,
set the TV for the
type signal you've
just connected (see
page 3 of this Set-
Up Guide.)
To select only the
channel numbers on
your Cable system
see “Auto Program"
(page 3). If you use a
Cable Converter box,
set the TV to the
same channel as the
converter's CH 3/4
switch (on the rear of
the converter.)
A ntenna
CoMiiiN vnoN IJHFA/MF
A combination antenna
receives normal
broadcast channels (VHP
2-13 and UHF14-69).
Your connection is easy
since there is only one
75Q (ohm) antenna plug
on the back of your TV -
and that’s where the anten­
na goes.
Si i-AK vn; IJIIF/VIIF
(^ome of you may have
kJtwo separate antennas.
One antenna is for VHP
channels (2-13) and the
other antenna is for UHP
channels (14-69).
Por homes with separate
UHPIVHP antennas, you
will need an optional
"combiner" before you can
connect to the TV. See the
"Smart Help" section (to
the right on this page) for
ordering details.
•C beòin F
ri
If your antenna has a
round cable (75 ohm) on the
end, then you're ready to con­
nect it to the TV.
If your antenna has flat twin-
lead wire (300 ohm), you first
need to attach the antenna wires
to the screws on a 300 to 75
ohm adapter.
Push the round end of the
adapter (or anteima) onto the
ANTENNA/CABLE plug on
the rear of the TV. If the round
end of the antenna wire is
threaded, screw it down tight.
Back of TV
Combination VHF/UHF Antenna
(Outdoor or Indoor)
Round
75C2
IBEQINI
<î>;
Attach the separate
UHF and VHF antennas to
the correct screws on the com­
biner.
Push the round end of the combiner
onto the ANTENNA/CABLE plug on
the rear of the TV.
Outdoor VHF Antenna
(Round 75 Ohm cable)
Round Cable 75Û
Remember,
be sure to set die
TV for the type sig­
nal you've connect­
ed (see page 3 of
this Set-Up Guide.)
To set the TV to
select only the
channel numbers in
your area see how
to “Program" or
"Add" channels in
memory on page 3.
To order any
optional acces.w/y
contact your dealer
or call the toll-free
accessory ordering
number (1-800-851-
8885):
• UHF/VHF
Combiner:
(SBV1133A01)
• 75-300 Ohm
Adapter:
(SBV1113A01)
• 300-75 Ohm
Adapter;
(483521827003)
VCR
TO
TV
B ask C onma i ion
J ^he basic Antenna, or
Cable TV, to VCR to
TV connection is shown to
the right. Por more infor­
mation on other hookups
(possible when Cable
Converter!Descrambler
boxes are included) refer
to your accessory VCR
and Cable Converter
Owner's Manual for
details.
---- 1BEQINI---------------------------------
- Connect your
Antenna or Cable TV signal
to the IN FROM ANT(enna)
plug on the VCR.
Connect the OUT TO TV
plug on the VCR to the
ANTENNA plug on the TV
(connecting cable supplied
with the VCR.)
Refer to the Owner's
Manual included with your
VCR for other possible con­
nections and TV/VCR operat
ing details.
Outdoor VHF/UHF
Antenna
300 to 75Î2 Ohm
Adapter
Back of TV
Cable TV signal
Round Cable
75£I Supplied with VCR
VCR