Milwaukee Tool 1001-1 V.2 - Manual (Page 2)

2 3
SPECIFICATIONS
Capacities
Wood Steel Masonry
Cat. No.
RAD KIT
Volts
AC
No
Load
RPM
RAD *
RPM
33° **
RPM
Flat
Boring
Bit
Hole
Saw
Auger
Bit
Ship
Auger
Bit
Selfeed
Bit
Twist
Drill
Hole
Saw
Carbide-
Tipped
Bit
1001-1
(3002-1)
120 0-600 lo 0-400
hi 0-900 0-600 1-1/2"
1-1/2"
1-1/2" 5"
5"
4" 1-1/2"
1-1/2"
1-1/2" 1-1/2"
1-1/2"
1-1/2" 3-5/8"
3-5/8"
2-9/16"
1/2"
1/2"
1/2" 3-1/2"
4-1/2"
3"
1/2"
1/2"
1/2"
1007-1
(***)
120 0-600 lo 0-400
hi 0-900 0-600 1-1/2"
1-1/2"
1-1/2" 5"
5"
4" 1-1/2"
1-1/2"
1-1/2" 1-1/2"
1-1/2"
1-1/2" 3-5/8"
3-5/8"
2-9/16"
1/2"
1/2"
1/2" 3-1/2"
4-1/2"
3"
1/2"
1/2"
1/2"
1101-1
(3102-1)
120 500 lo 0-335
hi 0-750 500 1-1/2"
1-1/2"
1-1/2" 5"
6"
4-1/2"
1-1/2"
1-1/2"
1-1/2" 1-1/2"
1-1/2"
1-1/2" 3-5/8"
4-5/8"
2-9/16"
1/2"
1/2"
1/2" 3-3/4"
5"
3-1/2"
1/2"
1/2"
1/2"
1107-1
(3107-1)
120 0-500 lo 0-335
hi 0-750 0-500 1-1/2"
1-1/2"
1-1/2" 5"
6"
4-1/2"
1-1/2"
1-1/2"
1-1/2" 1-1/2"
1-1/2"
1-1/2" 3-5/8"
4-5/8"
2-9/16"
1/2"
1/2"
1/2" 3-3/4"
5"
3-1/2"
1/2"
1/2"
1/2"
1107-6
(3107-6
120 0-500 lo 0-335
hi 0-750 0-500 1-1/2"
1-1/2"
1-1/2" 5"
6"
4-1/2"
1-1/2"
1-1/2"
1-1/2" 1-1/2"
1-1/2"
1-1/2" 3-5/8"
4-5/8"
2-9/16"
1/2"
1/2"
1/2" 3-3/4"
5"
3-1/2"
1/2"
1/2"
1/2"
1250-1
(***)
120 0-1000 lo 0-665
hi 0-1500
0-1000 1-1/2"
--
--
3-1/8"
--
--
1-1/2"
--
--
1-1/16"
--
--
2-1/4"
--
--
1/2"
--
--
1-3/4"
--
--
1/2"
--
--
* The Right Angle Drill Kit can be purchased with some drills, or as an accessory.
** The 33° Angle Drill Kit is available as an accessory only (Cat. No. 48-06-2860).
*** RAD available as an accessory only (Cat. No. 48-06-2871).
PERSONAL SAFETY
GENERAL POWER TOOL SAFETY WARNINGS
WORK AREA SAFETY
ELECTRICAL SAFETY
• Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
• Do not operate power tools in explosive atmos-
pheres, such as in the presence of fl ammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
• Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
• Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodifi ed plugs and matching outlets will
reduce risk of electric shock.
• Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet condi-
tions. Water entering a power tool will increase
the risk of electric shock.
• Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
• When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use
of a cord suitable for outdoor use reduces the risk
of electric shock.
• If operating a power tool in a damp location is
unavoidable, use a ground fault circuit inter-
rupter (GFCI) protected supply. Use of an GFCI
reduces the risk of electric shock.
• Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewel-
lery or long hair can be caught in moving parts.
• If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
WARNING READ ALL SAFETY WARNINGS AND ALL INSTRUCTIONS. Failure
to follow the warnings and instructions may result in electric shock, fi re and/or serious
injury.
Save all warnings and instructions for future reference. The term "power
tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated
(cordless) power tool.
POWER TOOL USE AND CARE
• Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
• Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must
be repaired.
• Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such pre-
ventive safety measures reduce the risk of starting
the power tool accidentally.
• Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
• Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits
etc. in accordance with these instructions, tak-
ing into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended could
result in a hazardous situation.
• Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the infl uence of drugs, alcohol or medi-
cation. A moment of inattention while operating
power tools may result in serious personal injury.
• Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
• Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
your fi nger on the switch or energising power tools
that have the switch on invites accidents.
• Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
SERVICE
• Have your power tool serviced by a qualifi ed
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
SPECIFIC SAFETY RULES
may make exposed metal parts of the power tool
“live” and could give the operator an electric shock.
• Maintain labels and nameplates. These carry
important information. If unreadable or missing,
contact a MILWAUKEE service facility for a free
replacement.
• WARNING Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities contains chemicals known to cause
cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• lead from lead-based paint
• crystalline silica from bricks and cement and
other masonry products, and
• arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are spe-
cially designed to fi lter out microscopic particles.
Fig. B Fig. C
Fig. A
GROUNDING
WARNING Improperly connecting the
grounding wire can result in the risk of elec-
tric shock. Check with a qualifi ed electrician
if you are in doubt as to whether the outlet is
properly grounded. Do not modify the plug
provided with the tool. Never remove the
grounding prong from the plug. Do not use
the tool if the cord or plug is damaged. If
damaged, have it repaired by a MILWAUKEE
service facility before use. If the plug will not
fi t the outlet, have a proper outlet installed by
a qualifi ed electrician.
The grounding prong in the plug is connected
through the green wire inside the cord to the
grounding system in the tool. The green wire in the
cord must be the only wire connected to the tool's
grounding system and must never be attached to
an electrically “live” terminal.
Your tool must be plugged into
an appropriate outlet, properly
installed and grounded in accord-
ance with all codes and ordinances.
The plug and outlet should look like
those in Figure A.
Double Insulated Tools:
Tools with Two Prong Plugs
Tools marked “Double Insulated” do not require
grounding. They have a special double insula-
tion system which satisfi es OSHA requirements
and complies with the applicable standards of
Underwriters Laboratories, Inc.,
the Canadian Standard Asso-
ciation and the National Elec-
trical Code. Double Insulated
tools may be used in either of
the 120 volt outlets shown in
Figures B and C.
Grounded Tools: Tools with Three Prong Plugs
Tools marked “Grounding Required” have a three
wire cord and three prong grounding plug. The
plug must be connected to a properly grounded
outlet (See Figure A). If the tool should electrically
malfunction or break down, grounding provides a
low resistance path to carry electricity away from
the user, reducing the risk of electric shock.
• Use auxiliary handle(s), if supplied with the
tool. Loss of control can cause personal injury.
• Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a “live” wire