CatEye CYCLOCOMPUTER CC-COM10W - Manual (Page 3)

3
COIN
Standard parts Optional parts
How to restart
After changing the battery, or when the computer displays an error, restart the computer
according to the following procedure.
With the restarting operation, the speed unit, date, tire size, and record data in the data view are retained. *
When the restarting operation is performed before 0:00 in the morning, the trip distance and the Car- *
bon offset for the day are not saved due to the data view’s update timing. To retain the measurement
data for the day, perform the restarting operation before starting measurement on the next day.
Refer to “Data view’s update timing” for the procedure to save the data view.
Press the 1. AC button on the back of the computer.
Set the date. To set the date, refer to “Preparing the computer-3”. 2.
At the time of setting the date, the latest record date in the data view is initially displayed, and any *
date before that cannot be set.
Set the clock. Refer to “Preparing the computer 4”. 3.
Maintenance
To clean the computer or accessories, use diluted neutral detergent on a soft cloth, and
wipe it off with a dry cloth.
Replacing the battery
Computer
If turns on, replace the battery. Install a new lithium battery
(CR2032) with the (+) side facing upward. After the battery change,
go through the restart operation, by pressing the AC button.
Then restart the computer according to “How to restart”. *
Sensor
When the speed is not displayed even after adjusting cor-
rectly, replace the battery. Install a new lithium battery
(CR2032) with the (+) side facing upward. After replacement,
check the positions of the sensor and magnet.
Troubleshooting
MODE does not work when the computer is mounted on its bracket.
Check that there is no dirt between the bracket and the computer.
Wash off the bracket with water to get rid of any dirt.
The sensor signal reception icon does not flash (the speed is not displayed). (Move the com-
puter near the sensor, and turn the front wheel. If the sensor signal reception icon flashes, this
trouble may be a matter of transmission distance due to battery drain, but not any malfunction.)
Check that the clearance between the sensor and magnet is not too large. (Clearance: within 5 mm)
Check that the magnet passes through the sensor zone correctly.
Adjust the positions of the magnet and sensor.
Is the computer installed at the correct angle?
Back of computer must face toward the sensor.
Check that the distance between the computer and sensor is correct. (Distance: within 20 to 70 cm)
Install the sensor within the specified range.
Is the computer or sensor battery weak?
In winter, battery performance diminishes.
Replace with new batteries. After replacement, follow the procedure “Replacing the battery”.
No display.
Is battery in the computer run down?
Replace it. Then restart the computer referring to “How to restart”.
Incorrect data appear.
Restart the computer referring to “How to restart”.
COIN
Specification
Battery Computer : Lithium battery (CR2032) x 1, Sensor : Lithium battery (CR2032) x 1
Battery life Computer : Approx. 1 years (If the computer is used for 1 hour/day; the battery life will vary
depending on the conditions of use.)
Sensor : Unit Total Distance reaches about 10000 km (6250 mile)
It may be shortened significantly when backlight is used frequently. *
This is the average figure of being used under 20 °C temperature and the distance between the *
computer and the sensor is 65 cm.
Controller ..........................4 bit, 1-chip microcomputer (Crystal controlled oscillator)
Display ..............................Liquid crystal display
Sensor ..............................No contact magnetic sensor
Transmission distance ......Between 20 and 70 cm
Tire circumference range ......0100 mm - 3999 mm (Initial value: 2096 mm)
Working temperature ........32 °F - 104 °F (0 °C - 40 °C) (This product will not display appropriately when
exceeding the Working Temperature range. Slow response or black LCD at lower or
higher temperature may happen respectively.)
Dimensions/weight Computer : 2-9/32” x 1-1/2” x 3/4” (58 x 38 x 19 mm) / 1.02 oz (29 g)
Sensor : 1-41/64” x 1-3/8” x 19/32” (41.5 x 35 x 15 mm) / 0.53 oz (15 g)
The factory-loaded battery life might be shorter than the above-mentioned specification. *
The specifications and design are subject to change without notice. *
CR2032 Open
Open
Close
Close
CR2032
#160-2190
Parts kit
#160-2196
Speed sensor
#160-0280
Bracket band
#166-5150
Lithium battery (CR2032)
#169-9691
Wheel
magnet
#160-2193
Bracket
#160-2770
Bracket holder