Cobra Electronics 15 BAND XRS 9770 - Manual (Page 7)

EasySet Programming
8 English
Your Detector
Mode Tone Display/Voice Result
Set
IntelliShield
City mode
default*
Two beeps City X A single beep sounds when the
signal is first detected.
One beep City X
beep Off Audio for all X band alerts are blocked
until signal strength reaches Level 3.
One beep City X+K Combines the City X mode with prevention
of K band audio alerts
until signal strength reaches Level 2.
IntelliMute
mode
Two beeps IntelliMute On All alerts (except for strobe signals from
emergency vehicles) are automatically
muted below the
engine rev point you set.
One beep IntelliMute Off Normal operation.
Set IntelliMute
RPMs
One beep Set IntelliMute
(see page 15
to set activation
point)
Allows you to set the engine
rev point while using IntelliMute.
Note: Only shown if IntelliMute is Off.
IntelliMute
Pro mode
Two beeps IntelliMute Pro
On All radar, VG-2 and Spectre detection is
turned Off below the engine rev set point.
One beep IntelliMute Pro
Off Normal operation.
Auto Mute
mode
Two beeps AutoMute On The audio volume of all alerts will be
automatically muted after four seconds for as
long as the signal is detected.
One beep AutoMute Off All alerts will sound at full volume
for as long as the signal is detected.
Set
Compass
One beep Set Compass Allows you to calibrate the compass.
(see page 18 to calibrate compass)
Pop Detect
mode
Two beeps Pop Detect On Unit will detect Pop signals.
One beep Pop Detect Off Unit will not detect Pop signals.
This EasySet programming menu lists all of the modes and settings you can
choose from after you have entered Program mode as described on page 7.
Mode Tone Display/Voice Result
VG-2 Detect
mode
Two beeps VG-2 Detect On Unit will detect VG-2 signals.
One beep VG-2 Detect Off Unit will not detect VG-2 signals.
VG-2 Audio
mode (not
shown if VG-2
detect is Off)
Two beeps VG-2 Audio On With VG-2 Detect On, the unit will give
audible alerts for VG-2 signals.
One beep VG-2 Audio Off With VG-2 Detect Off, the unit will give
only visual alerts for VG-2 signals.
Spectre
Detect mode
Two beeps Spectre
Detect On Unit will detect Spectre I & IV+ signals.
One beep Spectre
Detect Off Unit will not detect Spectre I & IV+
signals.
Spectre Audio
mode (not
shown
if Spectre
detect is Off)
Two beeps Spectre Audio
On With Spectre Audio On, unit will give
audible alerts for Spectre signals.
One beep Spectre Audio
Off With Spectre I Audio Off, unit will give only
visual alerts for Spectre I & IV+ signals.
SmartPower
mode
Two beeps SmartPower On SmartPower is On.
One beep SmartPower Off SmartPower is Off.
X Band
Detect mode
Two beeps X Band On Unit will detect X Band signals.
One beep X Band Off Unit will not detect X Band signals.
K or Ku Band
Detect mode
Two beeps K or Ku Band On Unit will detect K or Ku Band signals.
One beep K or Ku Band Off Unit will not detect K or Ku Band signals.
Set display
Dim mode
default*
Two beeps Display Dim Partially dimmed for dusk or night driving.
One beep Display Dimmer More dimmed for dusk or night driving.
One beep Display Dark Display is Off.
Restore factory
settings
One beep Restore Factory
Settings Resets user modes and settings to factory
default.
Exit program One beep EXIT PROGRAM Allows you to exit Program mode.
* The settings for these user modes can also be changed with
the one button method.See description of each user mode
(pages 10 and 25) for details.
Nothing Comes Close to a Cobra ® 9
Your Detector
EasySet Programming
XRS9770_MANL.indd 8-9 8/30/10 8:39 AM