G-Shock 5057 - Manual

Operation Guide 5057
1
MO0905- EA
30
Getting Acquainted
Congratulations upon your selection of this CASIO watch. To get the most out of your
purchase, be sure to read this manual carefully.
What to do if the center dial hand is stopped
The watch is shipped from the factory with the center dial
hand stopped in order to conserve battery power. Even
though the center dial hand is stopped, the watch
continues to maintain the current time internally. If the
center dial hand is stopped when you purchase the watch,
press any one of the watch’s buttons to start hand
movement.
Center dial hand
About This Manual
• Button operations are indicated using the letters shown
in the illustration.
• The upper right and center dials indicate various types
of data, depending on the currently selected mode.
• Each section of this manual provides you with the
information you need in order to perform operations in
each mode. Further details and technical information
can be found in the “Reference” section.
Note that CASIO COMPUTER CO., LTD. assumes no
responsibility for any damage or loss suffered by you or
any third party arising through the use of this product or
its malfunction. 30
Stopwatch second hand
24-hour
hand
Upper right
dial hand
Minute hand Hour hand
Day
Center dial hand
General Guide
30
30
▲
Press C.
Hold down A for about
three seconds. Timekeeping Mode
▲
Stopwatch Mode
Press B or D.
▲
Press D.
(When the stopwatch
is reset to all zeros.)
Press A.
30
Alarm Mode
30
Time/Date Adjustment
▲
▲
▲
Timekeeping
Use the Timekeeping Mode to set and view the current
time and date.
• Pressing A in the Timekeeping Mode will cause the
center dial hand to move to the current day of the week.
Press A to return to normal timekeeping. The watch
also will return to normal timekeeping if you do not
perform any operation for about two seconds.
30
30 3
Day
Press A.
▲▲
Hour hand Minute hand
24-hour
hand
Center dial (second) hand
Day of week
To set the time and date
1. In the Timekeeping Mode, hold down A for about three
seconds until the watch beeps.
• The stopwatch second hand and center dial hand will
move to 12 o’clock and stop there. This is the setting
mode.
2. Use D (+) and B (–) to change the time (hour and
minute) setting.
• As you set the time, take care to ensure that the
24-hour hand also is at the correct position.
3. After the time setting is the way you want, press C.
• This will cause the watch to beep and change to the
year setting mode.
30
Stopwatch second hand
Hour hand
Minute hand
Center dial hand
4. Use D and B to change the year setting.
• You can set the year within the range of 2000 to 2099.
• Use B to move the stopwatch second hand
clockwise to the value of the tens digit that you want
to specify. To set 2012, for example, move the hand to
10.
• Use D to move the center dial hand clockwise to the
value of the units digit that you want to specify. To set
2012, for example, move the hand to 2.
00
10
20
30 90
40
50
60
70
80 30
0
1
2
3
4
5
6
7
8
9
Stopwatch
second
hand
Center dial
hand
Setting the year (10s digit)
Setting the year (units digit)
7. After the month setting is the way you want, press C.
• This will cause the watch to beep and change to the
day setting mode.
8. Use D (+) and B (–) to change the day setting.
• When setting the day, the watch automatically will skip
days (30 and 31) that are not included in the currently
selected month. If you can’t select 30 or 31 when you
want to, check to make sure that the proper month is
selected.
• You can return to the time setting mode after
configuring the day setting by pressing C.
Pressing C will cause the watch to beep twice.
30
Dec
Jan
Feb
Mar Sep
Oct
Nov
Apr
May
Jun
Jul
Aug
Setting the Month
30 30
Day
Stopwatch second hand
Month
9. After all of the settings are the way you want and the day display is no longer
changing, press A. This will cause the center dial hand to start moving again and
the other hands to start moving from their current positions.
• You can press A at any time during the above procedure to return to the
Timekeeping Mode.
• The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to change
it except after you have the watch’s battery replaced.
• The date will change automatically when the current time reaches midnight. The
date change at the end of a month may take more time than normal.
Stopwatch
You can use the stopwatch to measure elapsed time,
cumulative elapsed time, and lap times. You also can input
the distance of the course or a particular segment of the
course of the race you are watching. That distance is used
along with the elapsed time, cumulative elapsed time, or
lap time measured by the watch to calculate and display
the average speed for the course or segment.
• See “Average Speed” for more information.
• Never operate the stopwatch while operating a
motor vehicle. Doing so is very dangerous and can
cause an accident.
• Entering the Stopwatch Mode causes the stopwatch
second hand, the upper right dial hand and center dial
hand to move to the 12 o’clock position.
• You can start elapsed time measurement with the
stopwatch while the watch is in the Stopwatch Mode or
the Timekeeping Mode.
30
Center dial (stopwatch
1/20 second) hand
* This hand rotates and
indicates the second count
during the first 60 seconds.
Upper right dial
(stopwatch minute) hand
Stopwatch second hand
• The display range of the stopwatch is 59 minutes, 59.95 seconds.
• The stopwatch continues to run, restarting from zero after it reaches its limit, until
you stop it.
• You can switch to another mode from the Stopwatch Mode only while the stopwatch
is stopped and reset to all zeros.
To start an elapsed time operation while in the Stopwatch Mode
1. In the Timekeeping Mode, press D to enter the Stopwatch Mode.
2. In the Stopwatch Mode, press B to start elapsed time measurement.
3. Press B to stop elapsed time measurement.
• You can restart and stop elapsed time measurement as many times as you like by
pressing B.
• The center dial hand rotates during the first 60 seconds only, and then stops. When
elapsed time measurement is stopped (by pressing B), the center dial hand jumps
to the 1/20 second indication (which is kept internally).
• Stopping a timing operation will cause the stopwatch second hand to stop at the
elapsed time seconds position. It will remain there if there is no distance value input.
If a distance value is input, the stopwatch second hand will then move to average
speed indication after about two seconds. After that it will move back to the elapsed
time second position.
• After you are finished measuring elapsed time, press D to reset the stopwatch to all
zeros.
• To return to the Timekeeping Mode, press D while the stopwatch is reset to all
zeros.
5. After the year setting is the way you want, press C.
• This will cause the watch to beep and change to the
month setting mode.
6. Use D to move the stopwatch second hand clockwise
to the month you want to specify. To set March, for
example, move the hand to 3 (Mar).