G-Shock GWF-T1030E-9JR - Manual (Page 7)

Operation Guide 3184
7
To change the Daylight Saving Time (summer time) setting
1. In the Timekeeping Mode, hold down A until the city
code starts to flash, which indicates the setting screen.
2. Press C and the DST setting screen appears.
3. Use D to cycle through the DST settings in the
sequence shown below.
Auto DST ( A vtA ) DST off (OFF) DST on (ON)
• If you change your Home City to one that is within the
same transmitter area, the current DST setting (Auto
DST) will be retained. If you change to a city that is
outside your current transmitter area, DST will be
turned off automatically.
DST indicator
Transmitter
Japan
China
U.S.
Europe (U.K., Germany)
None Covered City Codes
TPE, SEL, TYO
HKG, BJS
HNL, ANC, YVR, LAX, YEA, DEN, MEX, CHI, NYC, YHZ, YYT
LIS, LON, MAD, PAR, ROM, BER, STO, ATH, MOW
All other city codes
4. When the setting you want is selected, press A to exit the setting screen.
• The DST indicator appears to indicate that Daylight Saving Time is turned on.
Reference
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
Moon Phase Indicator
The Moon phase indicator of this watch indicates the
current phase of the Moon as shown below. It is based on
the view of the left side of the moon at meridian transit
from the northern hemisphere of the Earth. If the
appearance of the Moon phase indicator is reversed from
the actual Moon as viewed from your location, you can
use the procedure under “To reverse the displayed Moon
phase” to change the indicator.
Moon Phase indicator
Moon phase (part you can see)
Moon Phase
Indicator
Moon Age
Moon Phase
New
Moon First
Quarter
(Waxing)
28.7-29.8
1.0-2.7 2.8-4.6 4.7-6.4 6.5-8.3 8.4-10.1 10.2-12.0 12.1-13.8
0.0-0.9
(part you cannot see)
Moon Phase
Indicator
Moon Age
Moon Phase
13.9-15.7 15.8-17.5 17.6-19.4 19.5-21.2 21.3-23.1 23.2-24.9 25.0-26.8 26.9-28.6
Full
Moon Last
Quarter
(Waning)
Tidal Movements
Tides are the periodic rise and fall of the water of oceans, seas, bays, and other
bodies of water caused mainly by the gravitational interactions between the Earth,
Moon and Sun. Tides rise and fall about every six hours. The Tide Graph of this watch
indicates tidal movement based on the Moon’s transit over a meridian and the lunitidal
interval. The Tide Graph calculates and graphically represents current tide conditions
in your Home City or a port city in the vicinity of the Home City based on longitudes,
lunar day length, and lunitidal interval preset in watch memory, and on high tide times
specified by you.
Tide Graph
The Tide Graph graphically represents the current tide condition using one of three
patterns that represent spring tide, intermediate tide, and neap tide, as shown below.
Large difference between high tide
and low tide. Occurs a few days
before and after a New Moon and Full
Moon.
Medium difference between high tide
and low tide.
Small difference between high tide
and low tide. Occurs a few days
before and after the first quarter and
last quarter of a half Moon.
Tide Name Graph Description
• The Tide Graph flashes as shown below to indicate the tide range.
• The segments on either end of the Tide Graph flash during high tide.
Button Operation Tone
The button operation tone sounds any time you press one
of the watch’s buttons. You can turn the button operation
tone on or off as desired.
• Even if you turn off the button operation tone, alarms,
the Hourly Time Signal, and other beepers all operate
normally.
To turn the button operation tone on and off
1. In the Timekeeping Mode, hold down A until the city
code starts to flash, which indicates the setting screen.
2. Press C nine times until the current button operation
tone setting ( or ) appears.
3. Press D to toggle the setting between (tone on)
and (tone off).
4. Press A to exit the setting screen.
• The mute indicator is displayed in all modes when the
button operation tone is turned off.
Mute indicator
Power Saving Function
When turned on, the Power Saving function enters a sleep
state automatically whenever the watch is left in an area
for a certain period where it is dark. The table below
shows how watch functions are affected by the Power
Saving function.
Power saving indicator
Elapsed Time
in Dark
60 to 70 minutes
6 or 7 days
Display
Blank, with Power Saving
indicator flashing
Blank, with Power Saving
indicator not flashing
Operation
All functions enabled, except for the
display
Auto receive, beeper tone,
illumination, and display are disabled.
• Wearing the watch inside the sleeve of clothing can cause it to enter the sleep state.
• The watch will not enter the sleep state between 6:00 AM and 9:59 PM. If the watch
is already in the sleep state when 6:00 AM arrives, however, it will remain in the
sleep state.
• The watch will not enter a sleep state while in the Diving Mode, Stopwatch Mode, or
Countdown Timer Mode.
To recover from the sleep state
Perform any one of the following operations.
• Move the watch to a well-lit area.
• Press any button.
• Angle the watch towards your face for reading.
To turn Power Saving on and off
1. In the Timekeeping Mode, hold down A until the city
code starts to flash, which indicates the setting screen.
2. Press C 11 times until the Power Saving on/off screen
appears.
3. Press D to toggle Power Saving on ( ) and off ( ).
4. Press A to exit the setting screen.
• The Power Saving indicator is on the display in all
modes while Power Saving is turned on.
Radio-controlled Atomic Timekeeping Precautions
• Strong electrostatic charge can result in the wrong time being set.
• The time calibration signal bounces off the ionosphere. Because of this, such factors
as changes in the reflectivity of the ionosphere, as well as movement of the
ionosphere to higher altitudes due to seasonal atmospheric changes or the time of
day may change the reception range of the signal and make reception temporarily
impossible.
• Even if the time calibration signal is received properly, certain conditions can cause
the time setting to be off by up to one second.
On/Off status
l l
l l ll
l
ll
ll l lll ll
l ll
• The current time setting in accordance with the time calibration signal takes priority
over any time settings you make manually.
• The watch is designed to update the date and day of the week automatically for the
period January 1, 2000 to December 31, 2099. Setting of the date by the time
calibration signal cannot be performed starting from January 1, 2100.
• This watch can receive signals that differentiate between leap years and non-leap
years.
• Though this watch is designed to receive both time data (hour, minutes, seconds)
and date data (year, month, day), certain signal conditions can limit reception to time
data only.
• If you are in an area where proper time calibration signal reception is impossible, the
watch keeps the time with the precision noted in “Specifications”.
• If you have problems with proper time calibration signal reception or if the time
setting is wrong after signal reception, check your current city code, DST (summer
time), and auto receive settings.
• The Home City setting reverts to the initial default of TYO (Tokyo) whenever the
battery power level drops to Level 5 or when you have the rechargeable battery
replaced. If this happens, change the Home City to the setting you want.
Transmitters
The time calibration signal received by this watch depends on the currently selected
Home City code.
• When a U.S. time zone is selected, the watch receives the time calibration signal
transmitted from the United States (Fort Collins).
• When a Japanese time zone is selected, the watch receives the time calibration
signals transmitted from Japan (Fukushima and Fukuoka/Saga).
• When a European time zone is selected, the watch receives the time calibration
signals transmitted from Germany (Mainflingen) and England (Anthorn).
• When a China time zone is selected, the watch receives the time calibration signal
transmitted from China (Shangqiu City).
• When your Home City is LIS, LON, MAD, PAR, ROM, BER, STO, ATH, or MOW
(which can receive both the Anthorn and Mainflingen signals), the watch first tries to
pick up the signal it last successfully received. If that fails, it tries the other signal. For
the first receive after you select your Home City, the watch tries the nearest signal
first (Anthorn for LIS, LON, Mainflingen for MAD, PAR, ROM, BER, STO, ATH, and
MOW).
Spring Tide
Intermediate Tide
Neap Tide
Low tide
High tide High tide