Jaypro Sports 656 - Manual (Page 2)

ITEM QTY PART # DESCRIPTION
1 1 656U UPRIGHT 5 9/16 in OD
2 1 VARIOUS BACKBOARD
3 1 VARIOUS GOALS
4 1 BRC5916 5 9/16 in OD BAND CLAMP
5 2 SR5370 ANGLE BRACKET
6 2 BR45 SUPPORT BRACE
7 2 SR5368 TAB PERF BOARD
ITEM QTY PART # DESCRIPTION
8 2 HB5031 3/8-16 x 1 1/2 iN CARRIAGE BOLT
9 2 HS287 3/8"-16 x 1 1/4" HX HD CAP SCREW
10 2 HS288 3/8"-16 x 1 1/2" HEX HD CAP SCREW ZP
11 6 HW2050 3/8 in FLAT WASHER
12 6 HW334 3/8" MEDIUM SPLIT LOCK WASHER, ZP
13 6 HN264 3/8"-16 HEX NUT, ZP
14 2 HN5040 3/8-16 TEE NUT
Page 2 of 4
MODEL 656
5 9/16 in ROUND POST 6 FOOT EXTENSION,
DIRECT MOUNT
TOOLS REQUIRED:
9/16 in Socket Wrench and Combination Wrench
OPTIONAL 4 inch C CLAMP
BEFORE YOU START
A) UNPACK ALL PARTS AND CHECK AGAINST PARTS LIST TO ENSURE THAT ALL PARTS HAVE BEEN
INCLUDED
B) INSPECT FOR DAMAGE. REPORT ALL DAMAGES TO TRUCKING COMPANY.
UPRIGHT INSTALLATION
1) CHECK LOCAL BUILDING CODES BEFORE STARTING THE FOOTING, AS BUILDING CODES MAY VARY.
LOCAL BUILDING CODES SHOULD BE ADHEARED TO IF REQUIRENENTS ARE GREATER THAN THOSE
OUTLINED HERE.
2) DIG HOLE 36 INCHES SQUARE OR ROUND TO A DEPTH ON 58 INCHES, POUR AN 8 INCH FOOTING AND
ALLOW TO FULLY CURE OR PLACE UPRIGHT ON TWO 8 INCH CONCRETE BLOCKS.
3) POSITION AND SQUARE THE UPRIGHT ONTO THE FOOTING BASE. POUR THE REMAINDER OF THE
FOOTING. ALLOW THE CONCRETE TO FULLY CURE, PER THE MANUFACTURER'S INSTRUCTIONS, BEFORE
ATTACHING BACKBOARD AND GOAL. NOTE THE TOP HOLE OF THE BACKPOARD MOUNTING PLATE SHOULD
BE 119 INCHES OFF THE PLAYING SURFACE.
FINAL ASSEMBLY
4) ATTACH THE APPROPRIATE BRACE MOUNTING BRACKET TO THE BACK OF THE BACKBOARD, AS SHOWN
IN DETAIL D. THE BRACKET WILL DEPEND ON THE BACKBOARD ORDERED. THE BRACKETS WILL EITHER BE
INCLUDED WITH THE BACKBOARD OR FOUND IN THE GENERAL KIT. THE SPACING BETWEEN THE RIGHT
ANGLE BRACKETS OF THE RECTANGULAR STEEL BACKBOARD IS APPROXMATLY 36 INCHES. (FAN BOARDS
DO NOT REQUIRE REAR BRACING)
5) LIFT AND ATTACH THE BACKBOARD TO THE MOUNTING PLATE USING ONLY THE TOP TWO FASTENERS
AND TEE NUTS SHOWN IN SECTION A-A. WHEN THE BACKBOARD IS INSTALLED THE TEE NUTS SHOULD BE
UP AGAINST THE BACKBOARD AS SHOWN IN SEE DETAIL B. THE USE OF THE TEE NUTS ALLOW FOR EASY
REPLACEMENT OF THE GOAL. ( IF INSTALLING A FAN BOARD SKIP AHEAD TO STEP 9)
6)INSTALL THE BAND CLAMP TO THE UPRIGHT PIPE BY FIRST SPREADING THE BAND CLAMP OPEN ONLY
ENOUGH TO GET IT ONTO THE UPRIGHT. SEE DETAIL F
7) WITH THE HELP OF A C-CLAMP CLOSE THE BAND CLAMP BACK DOWN AND HOLD CLOSED BY INSTALLING
ONLY THE LOWER BOLT AND NUT FASTENERS. THE BAND CLAMP NEEDS TO BE APPROXIMATLEY 19 INCHES
FROM THE BACK SIDE OF THE BACKBOARD
8) INSTALL THE 1 5/16 DIA SUPPORT BRACES TO THE BACKBOARD AND BAND CLAMP AS SHOWN IN DETAILS
E AND F. PLUMB AND LEVEL THE BACKBOARD BEFORE TIGHTENING THE HARDWARE.
9) FINALLY ATTACH THE GOAL WITH THE REMAINING HARDWARE SHOWN IN SECTION A-A,
MAKE CERTAIN
THAT A WASHER IS PLACED BETWEEN THE BOARD AND THE GOAL IN THE LOWER TWO HOLES IN ORDER TO
KEEP THE GOAL PERPENDICULAR WITH THE BACKBOARD. NOTE THE ORIENTATION OF THE LOWER TWO
BOLTS. FOR ADDED SAFETY, THE EXPOSED THREADS AND NUTS SHOULD BE PLACED ON THE BACKSIDE OF
THE BACKBOARD, AS SHOWN IN SECTION A-A AND DETAIL C.
IMPORTANT NOTICE:
1)EQUIPMENT SHOULD BE CHECKED REGULARLY FOR PROPER
CONNECTING HARDWARE AND STRUCTURAL INTEGRITY. REPLACE
ANY DAMAGED OR MISSING HARDWARE IMMEDIATLY
2) USE OF THIS EQUIPMENT OTHER THAN INTENDED, MAY BE
HAZARDOUS.
3) ALTERATION OR MODIFICATION OF THIS EQUIPMENT MAY BE
HAZARDOUS AND RESULT IN INJURY. FOR REPAIR OR REPLACEMENT,
CONTACT JAYPRO SPORTS