Interlogix Simon XT Quick Start - Manual (Page 2)

To disarm (level 1):
1. Press Disarm.
2. Enter your code when the displays shows Enter Code.
The panel displays and speaks Disarmed, the Disarm
button lights up, and the panel beeps once.
To arm doors and windows (level 2):
1. Ensure that all doors and windows are closed.
2. Press
Doors+Windows.
3. Enter your code when the displays shows Enter Code,
if a code is required.
The panel displays Doors + Windows, speaks Doors and
Windows On, and the Doors+Windows button lights up.
The panel starts an exit delay and sounds exit beeps in
groups of two until the exit delay expires.
To arm motion sensors (level 3):
1. Press Motions.
2. Enter your code when the display shows Enter Code,
if a code is required.
The display shows Motions, speaks Motions On, and the
Motions button lights.
The panel starts an exit delay and sounds exit beeps in
groups of three until the exit delay expires.
To arm doors, windows, and motion sensors (level 4):
1. Press Doors+Windows.
2. Enter your code when the display shows Enter Code, if a
code is required.
3. While the panel is in the process of arming, press Motions.
The display shows Doors + Windows & Motions,
speaks Doors and Windows On, Motions On, and the
Doors+Windows and Motions buttons light up.
The panel starts an exit delay and sounds exit beeps in
groups of four until the exit delay expires.
Silent exit
Press Silent after you arm the system to silence status beeps.
The silent exit feature silences the status beeps that accompany
the exit delay. The panel will still beep at the beginning and end
of the exit delay.
Note: Enabling silent exit doubles the exit delay time.
Alarms
The system provides a series of alarms that indicate an unusual
occurrence. When an alarm is active, the display shows Alarm
Alarm Alarm, Press Status
.
To cancel the alarm, enter a valid master or user code. After
alarms are canceled, the system will be disarmed.
System status
Press Status (no code is required) to cause the system to display
and speak the following types of information:
•
Alarm conditions
• Alarm history
• Trouble conditions
• Open sensors
• Bypassed sensors
The Status button blinks when an active alarm exists. The Status
button is lit when an abnormal condition such as a trouble or open
sensor exists in the system.
You can clear certain status entries from the system (such as old
alarm history) by pressing Disarm after checking the status.
Touchpads and key fobs
You can use touchpads and key fobs to control the security
system from remote locations in and near your home. Interfacing
with the system using a touchpad is similar to using the panel.
Refer to the Simon XT User Manual and the touchpad or key fob
documentation for details.
Status beeps
The panel sounds status beeps to alert you to various system
events and conditions as shown in Table 3 below.
Table 3: Status beeps
Activity Beep
response
Doors+Windows Exit delay and entry delay beeps sound two times
every 5 seconds and two times per second during the
last 10 seconds.
Motions Exit delay and entry delay beeps sound three times
every 5 seconds and three times per second during the
last 10 seconds.
Doors+Windows
and Motions
Exit delay and entry delay beeps sound four times
every 5 seconds and four times per second during the
last 10 seconds.
Disarm One beep.
Chime Two beeps.
Special chime Three beeps.
Property/asset
management
One beep. (Information displays only on the Two-Way
Talking Touch Screen).
Trouble beeps Six beeps every minute. Press Status to stop beeps for
4 hours.
No activity beeps Twenty beeps every minute for 5 minutes (feature
must be programmed by the installer).
2 / 4 P/N 466-2399 • REV C • ISS 9JAN13