Heckler&Koch USP TACTICAL - Manual (Page 7)

12 13
Frame
All sides of the poly mer frame are tex tured to ensure a firm grip, even with wet hands
or under con di tions of rapid fire. The trig ger guard is slightly recurved and grooved to
provide a firm grip when using two hands or gloves to fire the pis tol. The frame is a one-
piece molded component with metal in serts (lock ing insert and guid ing part) cast into
the frame during production.
The slide rides on these metal inserts during op er a tion. The frame contains mounting
grooves for accessory attachment and finger recesses located to the left and right of the
magazine well for manual extraction of the mag a zine, if nec es sary. The serial num ber of
the pistol is en graved in the metal insert in cor po rat ed into the front of the frame in front
of the trigger guard, on the left side of the slide, and on the barrel locking block.
SiGHTS AND SiGHT ADjUSTMeNT
The USP Series Pistol uses the prov en 3-dot sighting ar range ment. By align ing all three
dots hor i zon tal ly on the tar get, with the front sight dot cen tered be tween the rear sight
dots, the op er a tor can quick ly and easily en gage the target with a high de gree of
ac cu racy. With the op tion al tritium sights with white outline in stalled, pre cise and rapid
target en gage ments are pos si ble under low light con di tions as well.
Fig. 6 Fig. 7 Fig. 8
Sights aligned Rear sight adjustment Front sight installation
Sights are set at the factory and generally do not require adjustment. The rear sight
can be adjusted for wind age by drifting the sight to the left or right, de pend ing on the
de sired shot placement. Bullet im pact on tar get will move in the same di rec tion that the
rear sight is moved. Be careful not to dam age the slide finish when ad just ing the sights.
Adjustments for elevation are ac com plished by ex chang ing the front sight with a higher
or lower sight. The height of the front sight is in di cat ed on the underside. The front
sight must be re moved by using a drift punch or a USP sight push er. The accessory sight
pusher can be used to install, remove, and adjust the front and rear sights on all USP
Series Pistols.
To raise the bullet impact on tar get, a shorter front sight is installed. To lower the bullet
impact on target, a taller front sight is installed. Installing the next high er or lower front
sight will change the point-of-impact 2 inches at 25 meters, depending on the am mu ni-
tion used. USP Series Pistols are function fired and ze roed at the fac to ry at 25 meters,
point-of-aim, point-of-impact. Your actual zero may vary depending on the ammunition
used and/or your style of shooting.
SeCTiON 4 AMMUNiTiON
WArNiNG: HK specifically disclaims any re spon si bil i ties for any damage or injury that
should occur because of, or as a result of, the use of faulty, remanufactured, or reloaded
(hand load ed) ammunition, or of cartridges oth er than those for which the pistol was orig i-
nal ly cham bered.
The USP Series Pistol is designed to fire quality, factory loaded am mu ni tion load ed to
SAAMI spec i fi ca tions for use spe cif i cal ly in handguns. For use with am mu ni tion with hard
primers (i.e. some NATO spec. cartridges), a spe cial hammer spring is avail able.
The following guidelines should be considered when se lect ing the cor rect am mu ni tion for
your pis tol.
1. Be sure the am mu ni tion you have chosen is com pat i ble with your pistol – proper
caliber, cartridge, bul let weight, etc. Caliber markings on the USP Pistol appear on
the left side of the slide and on the bar rel locking block, visible through the ejection
port on the right side of the slide.
2. Prior to loading the mag a zine and cham ber, carefully in spect all car tridg es for the
following ab nor mal i ties:
• Cracked, split, dirty or cor rod ed cases
• Improperly seat ed pro jec tiles and/or primers
• Damaged pro jec tiles
3. Do not attempt to fire a cartridge in which the pro jec tile has been forced back into
the case. Upon firing, this con di tion may result in increased chamber pres sure above
safe lim its.
4. Do not fire am mu ni tion through the pis tol that:
• Is for eign and/or out dat ed mil i tary sur plus
• Is as sem bled with cor ro sive prim er and/or propellant
• Is ex posed to oil, grease, wa ter, or direct sun light. Re move contaminants if pos si ble
be fore use and cool down am mu ni tion ex posed to di rect sun light or heat. (Ex po-
sure to sourc es of heat could raise the cham ber pres sure of the car tridge above safe
limits.)
• Is loaded spe cif i cal ly for use in submachine guns.
CAUTiON: HK firearms are designed to function with quality manufactured brass
cased ammunition. Use of steel or aluminum cased cartridges is not recommended
and could adversely affect safe and reliable functioning. For further information on
ammunition selection, contact HK Customer Service at 706-568-1906.
NOTe: in compliance with Nij Standard—0112.00, cur rent ly there are no known
am mu ni tion types that meet the general guide lines set forth in this sec tion that
are not compatible with the USP series pistols. All USPs are approved for use with
+P and +P+ ammunition as it applies to the specific caliber. The use of +P and +P+
ammunition accelerates wear and reduces the service life on the com po nent parts of
any pistol, including the USP series pistols.
NOTe: There is currently no existing SAAMi spec i fi ca tion +P or +P+ ammunition in
caliber .40 S&W.