Heckler&Koch USP TACTICAL - Manual (Page 14)

26 27
CLeAriNG THe PiSTOL
The pistol is not considered “clear” or safe unless:
1. The control lever (if applicable) is on “safe” and;
2. The magazine is removed from the pistol and;
3. The slide is locked to the rear and;
4. The chamber is free of brass or ammunition
To Clear the pistol:
1. Make sure fingers are outside of the trigger guard and the pistol is pointed in a safe
direction at all times!
2. Engage control lever (if applicable) - press the control lever upwards until the “S” (safe)
aligns with the reference line located on the frame.
3. Remove magazine - depress the magazine release lever and remove the magazine from
the pistol.
4. Open and lock slide - while keeping the pistol pointed in a safe direction, lock the slide
open by pulling the slide rearward as you press the slide release upward. Watch for a
cartridge or empty case to be ejected from the pistol.
5. Inspect chamber - inspect chamber for the presence of a cartridge or empty case by:
• Visually viewing chamber through the open ejection port and;
• Physically inserting a finger into the chamber through the ejection port to check
for the presence of a cartridge or empty case.
• Remove any cartridges or empty cases from the chamber or from within the pistol.
The Pistol is now considered “Clear.”
CAUTiON: A function check should be performed everytime the pistol has been
disassembled. The function check should be performed after the pistol is cleared (see
above).
FUNCTiON CHeCK (Variants 1 and 2)
1. Perform Clearing Procedure (see above) and ensure Control Lever is set on “S”.
2. Place muzzle in a safe direction and rack the slide to rear three or four times in quick
succession. The Slide should not bind when traveling back and forth on the frame.
3. “SAFE”: Let the slide go forward and completely go in to battery; the hammer should
now be cocked. With an unloaded pistol and the muzzle in a safe direction, ensure the
Control Lever is set on “S” and attempt to pull the trigger. The hammer must not fall.
4. “SINGLE ACTION”: Rotate the Control Lever to “F” (Fire) and with an unloaded USP
and the muzzle in a safe direction, attempt to pull the trigger and hold to the rear.
Hammer should fall
5. With the trigger still held towards the rear, rack the slide and release. The hammer
should be caught by the sear as signified by a metallic click.
6. Release the trigger completely and re-engage trigger. Hammer should fall.
7. “DOUBLE ACTION”: With the hammer now in the uncocked (up) position, pull the
trigger to the rear and hold. Hammer should fall.
8. With the trigger still held towards the rear, rack the slide and release. The hammer
should be caught by the sear as signified by a metallic click.
9. “DECOCK”: Pull down on the control lever, allowing the hammer to decock.
10. Place the Control Lever back on “S” (Safe).
FUNCTiON CHeCK (Variants 3 and 4)
1. Perform Clearing Procedure (see above).
2. Place muzzle in a safe direction and rack the slide to rear three or four times in quick
succession. The slide should not bind when traveling back and forth on the frame.
3. Let the slide go forward and completely go in to battery; the hammer should now be
cocked.
4. “SINGLE ACTION”: With the muzzle pointed in a safe direction, attempt to pull the
trigger and hold to the rear. Hammer should fall
5. With the trigger still held towards the rear, rack the slide and release. The hammer
should be caught by the sear as signified by a metallic click.
6. Release the trigger completely and re-engage trigger. Hammer should fall.
7. “DOUBLE ACTION”: With an unloaded pistol and the hammer now in the uncocked
(up) position, pull the trigger to the rear and hold. Hammer should fall.
8. With the trigger still held towards the rear, rack the slide and release. The hammer
should be caught by the sear as signified by a metallic click.
9. “DECOCK”: Pull down on the control lever, allowing the hammer to decock.
FUNCTiON CHeCK (Variants 5 and 6)
1. Perform Clearing Procedure (see above) and ensure Control Lever is set on “S”.
2. Place muzzle in a safe direction and rack the slide to rear three or four times in quick
succession. The Slide should not bind when traveling back and forth on the frame.
3. “SAFE”: Let the slide go forward and completely go in to battery; the hammer should
now be in the up (half-cocked) position. With an unloaded USP and the muzzle in a
safe direction, ensure the Control Lever is set on “S” and attempt to pull the trigger.
The hammer must not fall.
4. “DOUBLE ACTION”: Rotate the Control Lever to “F” (Fire) and with an unloaded USP
and the muzzle in a safe direction, attempt to pull the trigger and hold to the rear.
Hammer should fall.
5. With the trigger still held towards the rear, rack the slide and release. The hammer
should return to the up (half-cocked) position.
6. Pull the trigger to the rear and release. The hammer should return to the up (uncocked)
position.
7. Place the Control Lever back on “S” (Safe).