Great Planes Waco YMF-5D Biplane ARF - GPMA1295 - Manual (Page 4)

4
❏
1 oz. [30g] Medium Pro ™ CA+ (GPMR6008)
❏
1 oz. [30g] Thin Pro CA (GPMR6002)
❏
CA applicator tips (HCAR3780)
❏
CA debonder (GPMR6039)
❏
Pro 30-minute epoxy (GPMR6047)
❏
Pro 6-minute epoxy (GPMR6045)
❏
Epoxy brushes (6, GPMR8060)
❏
Mixing sticks (50, GPMR8055)
❏
Mixing cups (GPMR8056)
❏
Threadlocker ™ thread-locking compound (GPMR6060)
❏
R/C-56 canopy glue 4oz (JOZR5007)
❏
Medium T-pins (100, HCAR5150)
❏
#64 rubber bands (1/4 lb [113g] box, HCAQ2020)
❏
Milled fiberglass (GPMR6165)
❏
18" flexible steel rule (HCAR0460)
❏
Builder’s Triangle Set (HCAR0480)
❏
2-56 tap and drill set (GPMR8100)
❏
6-32 tap and drill set (GPMR8102)
❏
Tap handle (GPMR8120)
❏
Pliers with wire cutter (HCAR0625)
❏
Hobbico ® Heavy Duty Diagonal Cutter 7" (HCAR0627)
❏
Electric drill
❏
Household scissors
❏
Hobbico ball-end hex wrench set – metric (HCAR0521)
❏
Hobbico ball-end hex wrench set – SAE (HCAR0520)
❏
(2) 1" [25mm] C-Clamps
❏
Excel Small Clamp (EXLR5663)
❏
Easy-Touch ™ Bar Sander 5.5" (GPMR6169)
❏
Sandpaper assortment
❏
Masking tape
❏
Denatured alcohol (for epoxy clean up)
❏
Paper towels
❏
Plan protector (GPMR6167) or wax paper
Optional Supplies and Tools
❏
21st Century ® sealing iron (COVR2700)
❏
21st Century iron cover (COVR2702)
❏
Rotary tool such as Dremel ®
❏
Rotary tool reinforced cut-off wheel (GPMR8200)
❏
Dremel Drum Sander, Coarse 3/8" (DRER0968)
❏
Hobbico Retractable Fabric Tape Measure (HCAR0478)
❏
Hobbico Z-bend pliers (HCAR2000)
❏
Hobby Heat ™ micro torch (HCAR0755)
❏
Panel Line Pen (TOPQ2510)
❏
Dead Center ™ Engine Mount Hole Locator (GPMR8130)
❏
AccuThrow ™ Deflection Gauge (GPMR2405)
❏
Precision Magnetic Prop Balancer (TOPQ5700)
❏
Great Planes 1/5th scale WWI German Pilot (brown)
(GPMQ9115)
❏
Hobbico Pin Vise 1/16" Collet w/3 Bits (HCAR0696)
❏
Great Planes E-Z Mask Tape 1/8" (GPMR1000)
IMPORTANT BUILDING NOTES
• When you see the term test fit in the instructions, it means
that you should first position the part on the assembly
without using any glue, and then slightly modify or custom
fit the part as necessary for the best fit.
• Whenever the term glue is written you should rely upon
your experience to decide what type of glue to use. When
a specific type of adhesive works best for that step, the
instructions will make a recommendation.
• Whenever just epoxy is specified you may use either
30-minute (or 45-minute) epoxy or 6-minute epoxy. When
30-minute epoxy is specified it is highly recommended that
you use only 30-minute (or 45-minute) epoxy, because you
will need the working time and/or the additional strength.
• Photos and sketches are placed before the step they
refer to. Frequently you can study photos in following steps
to get another view of the same parts.
• The Waco YMF-5 is factory-covered with Top Flite ®
MonoKote ® film. Should repairs ever be required, MonoKote
can be patched with additional MonoKote purchased
separately. MonoKote is packaged in six-foot rolls, but
some hobby shops also sell it by the foot. If only a small
piece of MonoKote is needed for a minor patch, perhaps a
fellow modeler would give you some. MonoKote is applied
with a model airplane covering iron, but in an emergency a
regular iron could be used. A roll of MonoKote includes full
instructions for application. Following are the colors used on
this model and order numbers for six foot rolls.
Cub Yellow (TOPQ0220)
Black (TOPQ0208)
True Red (TOPQ0227)
• The stabilizer and wing incidences and engine thrust
angles have been factory-built into this model. However,
some technically-minded modelers may wish to check these
measurements anyway. To view this information visit the web
site at www.greatplanes.com and click on “Technical Data.”
Due to manufacturing tolerances which will have little or no
effect on the way your model will fly, please expect slight
deviations between your model and the published values.
KIT INSPECTION
Before starting to build, take an inventory of this kit to make
sure it is complete, and inspect the parts to make sure they
are of acceptable quality. If any parts are missing or are not of
acceptable quality, or if you need assistance with assembly,
contact Product Support. When reporting defective or
missing parts, use the part names exactly as they are written
in the Kit Contents list.
Great Planes Product Support:
3002 N Apollo Drive, Suite 1
Champaign, IL 61822
Telephone: (217) 398-8970, ext. 5
Fax: (217) 398-7721
E-mail: [email protected]