beautypg.com

Building stand, Ordering replacement parts – Great Planes Lanier RC Stinger II - GPMA1010 User Manual

Page 4

background image

4

Epoxy brushes 6, (GPMR8060)

Mixing sticks (GPMR8055)

Mixing cups (GPMR8056)

Pliers with wire cutter (HCAR0630)

T.A. Emerald Performance Duster Compressed Air
(TAEC1060)

Servo horn drill (HCAR0698)

Hobby Heat

micro torch II (HCAR0755)

Dead Center

Engine Mount Hole Locator (GPMR8130)

Precision Magnetic Prop Balancer (TOPQ5700)

AccuThrow

Deflection Gauge (GPMR2405)

CG Machine

(GPMR2400)

Hobbico Flexible 18" Ruler Stainless Steel (HCAR0460)

Top Flite MonoKote trim seal iron (TOPR2200)

Top Flite MonoKote heat gun (TOPR2000)

Hobbico Pin Vise 1/16 Collet w/6 Bits (HCAR0696)

Hobbico 8-Piece Ball Tip Hex L Wrench SAE
(HCAR0520)

Hobbico 7-Piece Ball Tip Hex L Wrench Metric
(HCAR0521)

Great Planes Clevis Installation Tool (GPMR8030)

Building Stand

A building stand or cradle comes in handy during the build.

We use the Robart Super Stand II (ROBP1402) for all our

projects in R&D, and it can be seen in pictures throughout
this manual.

IMPORTANT BUILDING NOTES

• When you see the term test fit in the instructions, it means

that you should first position the part on the assembly
without using any glue, and then slightly modify or custom

fit the part as necessary for the best fit.

Whenever the term glue is written you should rely upon

your experience to decide what type of glue to use. When
a specific type of adhesive works best for that step, the

instructions will make a recommendation.

Whenever just epoxy is specified you may use either

30-minute (or 45-minute) epoxy or 6-minute epoxy. When
30-minute epoxy is specified it is highly recommended that
you use only 30-minute (or 45-minute) epoxy, because you
will need the working time and/or the additional strength.

Photos and sketches are placed before the step they refer

to. Frequently you can study photos in following steps to get
another view of the same parts.

The stabilizer and wing incidences and engine thrust

angles have been factory-built into this model. However,
some technically-minded modelers may wish to check these
measurements anyway. To view this information visit the web
site at greatplanes.com and click on “Technical Data.” Due
to manufacturing tolerances which will have little or no effect
on the way your model will fly, please expect slight deviations
between your model and the published values.

ORDERING REPLACEMENT PARTS

Replacement parts for the Stinger II .46 ARF are available
using the order numbers in the Replacement Parts List
that follows. The fastest, most economical service can be

provided by your hobby dealer or mail-order company.

To locate a hobby dealer, visit the Great Planes web site

at greatplanes.com. Choose “Where to Buy” at the
bottom of the menu on the left side of the page. Follow the
instructions provided on the page to locate a U.S., Canadian
or International dealer.

Parts may also be ordered directly from Hobby Services

by calling (217) 398-0007, or fax at (217) 398-7721, but full
retail prices and shipping and handling charges will apply.

Illinois and Nevada residents will also be charged sales tax.
If ordering via fax, include a Visa

®

or MasterCard

®

number

and expiration date for payment.

Mail parts orders and payments by personal check to:

Hobby Services

3002 N. Apollo Drive, Suite 1

Champaign, IL 61822

Be certain to specify the order number exactly as listed in
the Replacement Parts List. Payment by credit card or
personal check only; no C.O.D.

If additional assistance is required for any reason, contact
Product Support by telephone at (217) 398-8970, or by
e-mail at [email protected].