Vermont Casting 1640 - Manual (Page 25)

25
Intrepid 1640 Woodburning Stove
30000830
Your stove is only one part of a system that includes the
chimney, the operator, the fuel and the home. The other
parts of the system will affect how well the stove works.
When there is a good match between all the parts, the
stove works well.
Wood stove operation depends on natural (unforced)
draft. Natural draft occurs when exhaust gas is hotter
(and therefore lighter) than the outdoor air at the top of
the chimney. The greater the temperature difference,
the stronger the draft. As the hot exhaust gas rises out
of the chimney it generates suction that draws air into
the stove for combustion. A slow, lazy fire with the
stove’s air inlets fully open indicates a weak draft. A
brisk fire, supported only by air entering the stove
through the normal inlets, indicates a good draft. The
inlets are passive; they regulate how much air can
enter the stove, but they do not move air into it.
The efficiency of a modern woodburning appliance, (in
which the amount of air available for combustion is
regulated), depends on the chimney to keep exhaust
gases warm all the way outdoors. The characteristics of
your chimney - whether it is steel or masonry, interior or
exterior, matched or mismatched to the stove collar -
determine how quickly it will warm up and how well it
will sustain the optimum temperatures necessary to
maintain strong draft and efficient combustion. Here
follows a description of various flue system characteris-
tics and related effects on stove performance.
Masonry Chimney
Although masonry is the traditional material used for
chimney construction, it can have distinct performance
disadvantages when used to vent a controlled-combus-
tion woodstove. Masonry forms an effective ‘heat sink’ -
that is, it absorbs and holds heat for long periods of
time. The large mass, however, may take a long time to
become hot enough to sustain a strong draft. The larger
the chimney (in total mass), the longer it will take to
warm up. Cold masonry will actually cool exhaust
gases enough to diminish draft strength. This problem
is compounded if the chimney is located outside the
home or if the chimney flue has a cross-sectional size
larger than the stove outlet.
Steel Chimney
Most factory-made ‘Class A’ steel chimneys have a
layer of insulation around the inner flue. This insulation
keeps the smoke warm and protects the surrounding
structure from the high flue temperatures. Because the
insulation is less dense than masonry, the inner steel
liner warms up more quickly than a masonry chimney.
Although steel chimneys are not as attractive as their
masonry counterparts, they are very durable and
generally outperform masonry.
Inside/Outside Location
Because the chimney’s function is to keep the smoke
warm, it is best to locate it inside the house. This
location uses the house as insulation for the flue and
allows some radiant heat release from the flue into the
home. Since an interior chimney does not continuously
lose its heat to the outdoors, it takes less heat from the
stove to get it warm and keep it warm.
Flue Sizing
The flue size for a controlled-combustion appliance
should be based on the cross-sectional volume of the
stove flue outlet. In this case, more is definitely not
better. Hot gases lose heat through expansion; if a
stove with a six-inch flue collar (28 square inch area) is
vented into a 10” x 10” flue, the gases will expand to
over three times their original volume. As gases cool
with expansion, draft strength decreases. If an over-
sized flue is also outside the house, the heat it absorbs
will be conducted to the outdoor air and the flue will
remain relatively cool.
It is common for a masonry flue to be oversized for the
stove. Such a chimney can take quite a while to warm
up and the stove performance will likely be disappoint-
ing. The best solution to an oversize flue problem is the
installation of an insulated steel chimney liner of the
same diameter as the appliance flue outlet. The liner
keeps the exhaust gas warm and the result is a stron-
ger draft. An uninsulated liner is a second choice -
although the liner will keep the exhaust restricted to its
original volume, the air around the liner will require time
and heat energy to warm up.
Check your local codes. You may be required to install
a flue liner in any oversize or masonry flue.
Pipe & Chimney Layout
Every bend in the flue will act as a brake on the ex-
haust as it flows from the firebox to the chimney cap.
The ideal pipe and chimney layout is straight up from
the stove through a completely straight chimney. Use
this layout if at all possible as it will promote optimum
stove performance and simplify maintenance.
If the stovepipe must elbow to enter a chimney, locate
the elbow about midway between the stove top and the
chimney thimble. This configuration lets the smoke
speed up before it must turn, keeps some pipe in the
room for heat transfer, and allows long-term flexibility
for installing a different appliance without relocating the
thimble.
Draft Management