Dromida DIDM1002 - Manual (Page 2)

OVERHEAT PROTECTION
If the temperature of the ESC is over the factory preset temperature for 5 seconds, the ESC will cut off the output power. If this happens, check for binding or broken
parts on the vehicle.
THROTTLE SIGNAL LOSS PROTECTION
The ESC will cut off the output power if the throttle signal from the transmitter is lost for 0.2 seconds.
PROGRAMMING
Running Mode: This function adjusts the running mode between forward/brake and forward/brake/reverse.
Drag Brake Force: This function adjusts the amount of drag brake applied at neutral throttle to simulate a slight braking effect of a neutral brushed motor while coasting.
Low Voltage Cut-Off (LVC): This program is used to prevent the LiPo battery from over-discharging. The ESC monitors the battery’s voltage. At any time, if the
battery’s voltage is lower than the designated value, the output power will be reduced to 50%. After 10 seconds the ESC will completely cut the output power off.
Start Mode (Punch): This function adjusts the amount of initial power when the trigger is applied.
Maximum Brake Force: This program adjusts the amount of overall brake force applied when at full brake.
During programming the ESC the motor will emit a “beep” tone at the same time the LED flashes. A long time flash and long “beep” represents “5” so it is easy to
identify items with large numbers.
For example:
A long time flash (motor sounds “beeeep”) equals a value of 5.
A long time flash + 1 short flash (motor sounds “beeeep-beep”) equals a value of 6.
A long time flash + 2 short flashes (motor sounds “beeeep-beep-beep”) equals a value of 7.
90 DAY LIMITED WARRANTY
PLEASE DO NOT RETURN YOUR PRODUCT TO THE STORE! Dromida will repair or replace factory defects for 90 days from the date of purchase. This warranty
specifi cally does not cover crash damage, misuse or abuse. To make a warranty claim, please contact our product support team at 1-217-398-8970 or e-mail us
at [email protected].
If requested by Product Support, please send defective product to: Hobby Services, 3002 N Apollo Dr., Suite #1, Champaign, IL 61822.
This warranty applies only if the product is operated in compliance with the instructions and warnings provided with each model. Dromida assumes no liability except
for the exclusive remedy or repair of parts as specifi ed above. Dromida shall not be liable for consequential or incidental damages. Some states do not allow the
exclusion of consequential or incidental damages so the above exclusion may not apply to you. This warranty gives you specifi c legal rights and you may also have
other rights which vary from state to state.
ESC OFF
Turn on Tx
TO COMPLETE PROGRAMMING, SWITCH OFF THE ESC, AND THEN SWITCH IT ON
To adjust RUNNING MODE,
release SET button.
To adjust the value in the mode, press the SET button until the
desired value is reached.
Hold SET button
for 6 SECONDS
Hold SET button
for 9 SECONDS
Hold SET button
for 12 SECONDS
Hold SET button
for 15 SECONDS
Hold SET button
for 18 SECONDS
To adjust DRAG BRAKE FORCE,
release SET button.
To adjust LVC,
release SET button.
To adjust PUNCH,
release SET button.
To adjust MAX BRAKE FORCE,
release SET button.
Hold SET Button
Switch on ESC
Red LED Flashes
Red LED Flashes 1 TIME = FORWARD/BRAKE
Red LED Flashes 2 TIMES = FORWARD/BRAKE/REVERSE
Red LED Flashes 1 TIME = SOFT Initial Start
Red LED Flashes 2 TIMES = NORMAL Initial Start
Red LED Flashes 3 TIMES = AGGRESSIVE Initial Start
Red LED Flashes 4 TIMES = VERY AGGRESSIVE Initial Start
Red LED Flashes 1 TIME = SOFT Brake Force
Red LED Flashes 2 TIMES = NORMAL Brake Force
Red LED Flashes 3 TIMES = AGGRESSIVE Brake Force
Red LED Flashes 4 TIMES = VERY AGGRESSIVE Brake Force
Red LED Flashes 1 TIME = NO LVC
Red LED Flashes 2 TIMES = 2.6V LVC
Red LED Flashes 3 TIMES = 2.8V LVC
Red LED Flashes 4 TIMES = 3.0V LVC
Red LED Flashes 5 TIMES = 3.2V LVC
Red LED Flashes 6 TIMES = 3.4V LVC
Red LED Flashes 1 TIME = 0% Drag Force
Red LED Flashes 2 TIMES = 5% Drag Force
Red LED Flashes 3 TIMES = 10% Drag Force
Red LED Flashes 4 TIMES = 15% Drag Force
Red LED Flashes 5 TIMES = 20% Drag Force
Red LED Flashes 6 TIMES = 25% Drag Force
Red LED Flashes 7 TIMES = 30% Drag Force
Red LED Flashes 8 TIMES = 40% Drag Force
RUNNING MODE
Green LED Flashes 1 TIME
DRAG BRAKE FORCE
Green LED Flashes 2 TIMES
LOW VOLTAGE CUTOFF (LVC)
Green LED Flashes 3 TIMES
START MODE (PUNCH)
Green LED Flashes 4 TIMES
MAX BRAKE FORCE
Green LED Flashes 5 TIMES
To reset to the factory default settings, set the throttle to neutral and hold the “SET” button for 3 seconds. The red and
green LED will slowly flash at the same time to indicate the ESC has been restored to the factory default settings.
We try very hard to have accurate and up-to-date information in this document. Any errors are unintentional.
dromida.com DIDM1002 v1.0 © 2014 DROMIDA, A HOBBICO COMPANY