JVC SX-LC3WD - Manual (Page 3)

Connection
Anschluß
Raccordement
Aansluiting
Conexión
Collegamento
Anslulting
Tllslutning
LIitäntä
iîS
Silver
Siber
Argent
Zilver
Plata
Argent
Silverfärg
Seivfarvede
Hopeanvarinen
iSÖfe
Fit the speaker cord into the groove, then
turn the knob clockwise to fasten the cord.
Das Lautsprecherkabel in die Nut einpassen
und dann den Knopf im Uhrzeigersinn
drehen, um das Kabel zu befestigen.
Insérer le cordon d’enceinte dans la
rainure, puis tourner le bouton vers la
droite pour fixer le cordon.
Leg het luidsprekersnoer in de groef en
draai vervolgens de knop met de kiok
mee vast.
Fije el cable del altavoz en la ranura, y
después gire el mando bacia la derecha
para fijarlo.
Inserire il filo dell’altoparlante nella
scanalatura e poi girare il pomello in
senso orario per fissarlo e così
assicurare il collegamento.
Passa in varje hogtalarkabels kärna i
respektive spar och vrid därefter pâ
ratten for att dra fast kabeln.
Anbring hojttalerkablet i rillen og drej
derefter skruen i retningen mod uret for
at fastgore kablet.
Sovita kaiutinjohto aukkoon ja kiinnitä
johto Sitten paikalleen kääntämällä
nuppia myötäpäivään.
CONNECTION
• Connect the LEFT speaker terminals of the amplifier to the
LEFT terminals of the speaker and RIGHT to RIGHT using
the attached speaker cords as shown in the figure making
sure polarity is correct; (+) to (+) and (-) to (-). Connect the
silver speaker wire to the (-) terminal.
• Turn off power to the whole system before connecting the
speakers to the amplifier.
• The nominal impedance of the SX-LC3WD is 6 Q. Select
for use an amplifier to which a speaker system with the
load impedance of 6 Q can be connected.
• The maximum power handling capacity of the SX-LC3WD
is 120 W. Excessive input will result in abnormal noise and
possible damage. In cases where the signals described be­
low are applied to the speakers, even if the signals are be­
low the maximum allowable input, they may cause an over­
load and burn the wiring of the speakers. Be sure to lower
the amplifier volume beforehand.
1) Noise during FM tuning.
2) High level signals containing high frequency components
produced by a tape deck in the fast forward mode.
3) Click noise produced when turning power of other com­
ponents on and off.
4) Click noise produced when connecting or disconnecting
cords with the power on.
5) Click noise produced when the cartridge is replaced with
the power on.
6) Click noise produced when operating amplifier switches.
7) Continuous high frequency oscillation or high pitch elec­
tronically produced musical instrument sound.
8) Howling when using a microphones.
1. Remove the ending part of the vinyl covering from the cut.
2. Twist the wires.
1. Entfernen Sie dan Endstück der Vinylhüle von dem
geschnittenen Teil.
2. Drehen Sie die Kabel.
1. Enlever la partie d’extrémité du recouvrement vinylique de
la partie déoupée.
2. Tordre les fils.
1. Snijd het laatste gedeelte van de vinylmantel af en ven/vijder.
2. Draai de draadkernen ineen.
1. Quitar la parte de la extremidad de la cubierta de plástico
de la parte cortada.
2. Torcer los alambres.
1. Rimuovete l’estremità della copertura in plastica dalla parte tagliata.
2. Torcete i fili.
1. Dra loss den avskurna deien av isoleringen fràn kabeländen.
2. Tvinna tràdarna.
1. Fjern enden af vinyl-isoleringen, hvor den er klippet af.
2. Sno tràdene.
1. Irrota muovipeitteen loppupää uurteesta.
2. Kierrä johdot.
1.
SPECIFICATIONS
Type
Speakers
Woofer
Tweeter
Power Handling Capacity
Impedance
Frequency Range
Sound Pressure Level
Dimensions (W x H x D)
Mass
Accessories
D e s ig n a n d s p e c ific a tio n s
: 2-way bass-reflex type
(Magnetically-shielded type)
13.5 cm (5-3/8 in.) cone x 2
1.9 cm (3/4 in.) dome x 1
120 W
6 L I
48 Hz-80 000 Hz
88 dB/W-m
150 mm x 416.5 mm x 292.5 mm
(5-15/16 in. X 16-7/16 in. X 11-9/16 in.)
8.0kg (17.6 lbs) each
Speaker cord ............... 1
Spacers........................ 4
s u b je c t to c h a n g e w ith o u t n o tic e .