Accessories, Click for where to buy – CAMCORP Cartridge Collector User Manual
Page 35
Phone
800-323-2593
630-231-5900
Fax
630-231-1377
National Controls
Corporation
4
Previous
Next
4-9
8” x 6” x 3
1
/
2
”
10” x 8” x 4”
Accessories:
C
A
D
B
.25
.31
.25 Dia. Hole
(4 Pl.)
L1
L2
AC
Voltage
Input
C
1
2
Solenoid Valve
OFF & ON Time
Adjustments
Program Wire-
Determines number
of outputs to be
activated
Pressure Switch Input-
For on demand cleaning.
(Controls are shipped with
inputs shorted out)
(4250-2 10/92)
.625
2.0 Max.
.050 Aluminum
Chassis
NOTE: Not all components are shown.
Component locations can vary from model
to model.
DNC-T2003 THRU T2032
OFF ON
3 AMP
# 6 screw typ.
WIRING DIAGRAM
Maximum No.
of
Outputs
Dimensions
A B C D
Size of
NEMA-4 Encls.
Required
Programmable
No. of
Outputs
Off Time
In
Seconds
Part
Number
3
6
3
/
4
” 4
7
/
8
” 6
1
/
4
” 4
1
/
4
”
8” x 6” x 3
1
/
2
”
1 - 3
1.5 - 30
DNC-T2003-A10
8.5 - 180
DNC-T2003-B10
6
8
3
/
4
” 6
7
/
8
” 8
1
/
4
” 6
1
/
4
”
10” x 8” x 4”
2 - 6
1.5 - 30
DNC-T2006-A10
8.5 - 180
DNC-T2006-B10
10
8
3
/
4
” 6
7
/
8
” 8
1
/
4
” 6
1
/
4
”
10” x 8” x 4”
3 - 10
1.5 - 30
DNC-T2010-A10
8.5 - 180
DNC-T2010-B10
20
10
3
/
4
” 8
7
/
8
” 10
1
/
4
” 8
1
/
4
”
12” x 10” x 5”
11 - 20
1.5 - 30
DNC-T2020-A10
8.5 - 180
DNC-T2020-B10
32
12
3
/
4
” 10
7
/
8
” 12
1
/
4
” 10
1
/
4
”
14” x 12” x 6”
17 - 32
1.5 - 30
DNC-T2032-A10
8.5 - 180
DNC-T2032-B10
Maximum No.
of
Outputs
Dimensions
A B C DD
Size of
NEMA-4 Encls.
Required
Programmable
No. of
Outputs
Off Time
In
Seconds
Part
Number
6
6
3
/
4
” 4
7
/
8
” 6
1
/
4
” 4
1
/
4
”
10” x 8” x 4”
2 - 6
1.5 - 30
DNC-T2006-A220
8.5 - 180
DNC-T2006-B220
10
6
3
/
4
” 4
7
/
8
” 6
1
/
4
” 4
1
/
4
”
10” x 8” x 4”
3 - 10
1.5 - 30
DNC-T2010-A220
8.5 - 180
DNC-T2010-B220
20
10
3
/
4
” 8
7
/
8
” 10
1
/
4
” 8
1
/
4
”
12” x 10” x 5”
11 - 20
1.5 - 30
DNC-T2020-A220
8.5 - 180
DNC-T2020-B220
32
12
3
/
4
” 10
7
/
8
” 12
1
/
4
” 10
1
/
4
”
14” x 12” x 6”
17 - 32
1.5 - 30
DNC-T2032-A220
8.5 - 180
DNC-T2032-B220
DNC-T2003 through DNC-T2032 120VAC Input Voltage
DNC-T2006 through DNC-T2032 220VAC Input Voltage
Enclosure For:
Dimensions
Part Number
DNC-T2003
BOX-A0806-CHNF
DNC-T2006
BOX-A1008-CHNF
DNC-T2010
10” x 8” x 4”
BOX-A1008-CHNF
DNC-T2020
12” x 10” x 5”
BOX-A1210-CHNF
DNC-T2032
14” x 12” x 6”
BOX-A1412-CHNF
Pilot Lamp
NEMA-4 Rated Red Light
ASL-00RED-NEMA4
On/Off Switch
NEMA-4 Rated w/Legend Plate
MSW-0DPST-011
Alternate Action Dual Coil Latch Relay
KDD-LATCH-120AC
Socket For Latch Relay
MSO-0D11P-012
National Controls Corporation offers NEMA 4 type enclosures for mounting our controls. These enclosures are made of heavy gauge steel and have a
continuous hinge cover. All seams are continuously welded. The finish is gray hammer-tone enamel inside and out, over phosphatized surfaces.
Note. In order to keep abreast of the latest technology, National Controls Corporation reserves the right to change components and/or design of
controls without notice.
Note: Special time ranges are availabale with the following maximum to minimum time ratio restrictions: ON Time - 10:1; Off Time - 20:1
Important Notice to Users:
Our timers are capable of use in a
wide array of devices and in various
applications. Any device or system
incorporating a timer should be so
designed that, in the event of failure,
malfunction or normal wear-out of
the timer, the system will become
inoperative in a manner which will
prevent property damage or bodily
Injury.
Caution:
1. Do not mount controls in high
vibration areas without shock
mounts.
2. Do not mount controls in areas of
high dust or corrosive atmospheres
without a protective enclosure.
3 Do not use a converter or inverter
for the power source.
4. Do not mount control in high
transient voltage areas without an
isolation transformer
5. Do not leave control box open.
6. Do not allow a local repair shop to
repair the controls, as we employ
some very sophisticated components
that could be further damaged. For
service, call us directly: 800-323-2593
Click for Where to Buy