Pro-Link 47% OMU 350 Finish 14256 EN - Manual

47% OMU 350
Finish
NFPA/HMIS : Health -1
Flammability - 2
Reactivity - 0
Complies With USDL Safety and Health Regulations, (29 CFR 1910.200)
Material Safety Data Sheet US Department Of Labor
SECTION - 1 CHEMICAL AND COMPANY IDENTIFICATION
PRODUCT USE: Wood Floor Coating
Pro Link
500 Chapman Street
Canton, MA 02021
EMERGENCIES: 1-800-255-3924
REVISION DATE: 01/14/2013
SECTION - 2 HAZARDS INFORMATION
Primary Route(s) of Entry: Skin contact /absorption and inhalation
Signs and Symptoms of Overexposure: Gastrointestinal irritation
(nausea, vomiting, diarrhea), irritation to nose, throat, and respiratory tract.
Target Organ Effects: None expected.
IMMEDIATE HEALTH EFFECTS
EYES: Exposure may cause noticeable pain, and severe irritation.
SKIN: Exposure may cause mild skin irritation. Prolonged or repeated
exposure may dry the skin. Symptoms may include redness, burning, and
drying and cracking. Additional symptoms of skin contact may include:
allergic reaction. Skin absorption is possible, but harmful effects are not
expected from this route of exposure under normal handling and use.
INHALATION: Exposure to vapor or mist is possible. Short term inhalation
is no likely to cause harmful effects: breathing large amounts may be
harmful. Symptoms are more typically seen at air concentrations
exceeding the recommended exposure limits.
INGESTION: Single dose oral toxicity is low. Swallowing small amounts
during normal handling is not likely to cause harmful effects: swallowing
large amounts may be harmful.
REPRODUCTIVE / DEVELOPMENTAL INFORMATION No Data
CARCINOGENIC INFORMATION: This material is not listed as a
carcinogen by IARC, NTP, or OSHA
LONG TERM EFFECTS: No Data
SECTION - 3 COMPOSITION ON INGREDIENTS
CAS # CHEMICAL NAMES Wt% TLV (UNITS)
8052-41-3 Stoddard Solvent. < 40 100 (PPM)
556-67-2 Octamethylcyclotetrasiloxane <15 N/E
N/E = not established
SECTION - 4 FIRST AID MEASURES
EYES- Immediately flush with water. Remove contact lenses if applicable,
and continue flushing with water. call a physician if irritation persists.
SKIN- Flush with water. Wash thoroughly with soap and water. Call
physician if irritation persists.
INHALATION- If symptoms develop, move victim to fresh air. If symptoms
persist call a physician.
INGESTION- Do not induce vomiting. Rinse mouth with water, then drink
one glass of water. Call a physician immediately. Never give anything by
mouth if victim is unconscious, is rapidly losing consciousness or is
convulsing.
SECTION - 5 FIRE FIGHTING MEASURES
Flash Point 110 degrees F(C.C. method)
Explosive limits Unknown
Hazardous Products of Combustion Carbon Dioxide, Carbon Monoxide
Extinguishing Media Dry Foam
Fire Fighting Instructions Avoid walking in spilled material. Avoid
contact with this material. Wear protective clothing for skin and eyes
SECTION - 6 ACCIDENTAL RELEASE MEASURES
Small Spill: Absorb with an inert solid and scoop up for disposal, then rinse
soiled area with water down the drain.
Large Spill: Stop leak at the source and collect into a suitable container,
then treat as a small spill.
SECTION - 7 HANDLING AND STORAGE
Handling: Containers of this material may be hazardous when emptied.
Since emptied containers retain product residues (vapor, liquid, and/or
solid), all hazard precautions given in the data sheet must be observed.
Storage: Store in a cool, dry place. Keep container closed when not in
use.
SECTION - 8 EXPOSURE CONTROLS / PERSONAL PROTECTION
Eye Protection: Chemical Splash goggle in compliance with OSHA
regulations are advised: however , OSHA regulations also permit other type
safety glasses. Consult your safety representative.
Skin Protection: Wear rubber gloves (consult your safety equipment
supplier). To prevent repeated or prolonged skin contact, wear impervious
clothing and boots.
Respiratory Protection: If workplace exposure limits of product or any
component are exceeded (see exposure guidelines), NIOSH/OSHA
approved air supplied respirator is advised in the absence of proper
environmental control. OSHA relations also permit other NIOSH/OSHA
respirators (negative pressure type) under specific conditions (see your
industrial hygienist). Engineering or administrative controls should be
implemented to reduce exposure.
Engineering Controls: Provide sufficient mechanical (general and local
exhaust) ventilation to maintain exposure below level of overexposure (from
known, suspected or apparent adverse effects).
SECTION - 9 PHYSICAL AND CHEMICAL PROPERTIES
Appearance and odor Thin, Amber liquid with a Characteristic Odor
pH Concentrate NA
Vapor Pressure Unknown
Vapor Density Unknown
Boiling Point 212 Degrees Fahrenheit
Solubility in Water Complete
Percent Volatile 43%
Specific Gravity (H2O =1) 1.01 +/- 0.02
SECTION - 10 STABILITY AND REACTIVITY
Chemical Stability Stable
Conditions to Avoid Temperature Extremes
Incompatibility None
Hazardous Decomposition Will not Occur
Hazardous Polymerization Will not Occur
SECTION - 11 TOXICOLOGICAL INFORMATION
No Data Available
SECTION - 12 ECOLOGICAL INFORMATION
No Data Available