beautypg.com

Pro-Link Refresh - Restorative Maintainer 10042 User Manual

Refresh

background image


Refresh


NFPA/HMIS :
Health -1
Flammability - 0
Reactivity - 0

Complies With USDL Safety and Health Regulations, (29
CFR 1910.200) Material Safety Data Sheet
US Department Of Labor

SECTION - 1 CHEMICAL AND COMPANY

IDENTIFICATION


PRODUCT NAME: Refresh
PRODUCT USE: Neutral Cleaner

PRO-LINK
510 Chapman Street
Canton, MA 02021

EMERGENCIES: 1-866-303-6948
REVISION DATE: 02/14/05

SECTION - 2 COMPOSITION ON

INGREDIENTS

CAS # CHEMICAL NAMES Wt% TLV (UNITS)

9016-45-9 Nonoxanol < 12.0 N/E
N/E = not established

SECTION - 3 HAZARDS INFORMATION


Primary Route(s) of Entry Skin contact /absorption and
inhalation
Signs and Symptoms of Overexposure Gastrointestinal
irritation (nausea, vomiting, diarrhea), irritation to nose,
throat, and respiratory tract.
Target Organ Effects: None expected.

IMMEDIATE HEALTH EFFECTS

EYES: Exposure may cause noticeable pain, and severe
irritation.
SKIN: Exposure may cause mild skin irritation. Prolonged or
repeated exposure may dry the skin. Symptoms may include
redness, burning, and drying and cracking. Additional
symptoms of skin contact may include: allergic reaction.
Skin absorption is possible, but harmful effects are not
expected from this route of exposure under normal handling
and use.
INHALATION: Exposure to vapor or mist is possible. Short
term inhalation is no likely to cause harmful effects:
breathing large amounts may be harmful. Symptoms are
more typically seen at air concentrations exceeding the
recommended exposure limits.
INGESTION: Single dose oral toxicity is low. Swallowing
small amounts during normal handling is not likely to cause
harmful effects: swallowing large amounts may be harmful.

REPRODUCTIVE / DEVELOPMENTAL INFORMATION
No Data

CARCINOGENIC INFORMATION
This material is not listed as a carcinogen by IARC, NTP, or
OSHA

LONG TERM EFFECTS: No Data

SECTION - 4 FIRST AID MEASURES

Eye Contact: Immediately flush with water. Remove
contaminated clothing or shoes. Get medical attention if
symptoms occur.
Ingestion: Induce vomiting immediately as directed by
medical personnel. Get medical attention Drink water. Get
Medical attention. NEVER GIVE ANYTHING BY MOUTH
TO AN UNCONSCIOUS PERSON.

SECTION - 5 FIRE FIGHTING MEASURES


Flash Point Explosive limits
No Flash at Boil (C.C. method) Not Applicable

Autoignition Temperature Hazardous Products of
Not Applicable Combustion
Not Applicable

Extinguishing Media Fire Fighting Instructions
Not Applicable Avoid contact with this material.
Avoid walking in spilled material.
Wear protective clothing for skin
and eyes

SECTION - 6 ACCIDENTAL RELEASE

MEASURES

Small Spill: Absorb with an inert solid and scoop up for
disposal, then rinse soiled area with water down the drain.

Large Spill:Stop leak at the source and collect into a
suitable container, then treat as a small spill.

SECTION - 7 HANDLING AND STORAGE

Handling: Containers of this material may be hazardous
when emptied. Since emptied containers retain product
residues (vapor, liquid, and/or solid), all hazard precautions
given in the data sheet must be observed.

Storage: Store in a cool, dry place. Keep container closed
when not in use.

SECTION - 8 EXPOSURE CONTROLS /

PERSONAL PROTECTION


Eye Protection: Chemical Splash goggle in compliance with
OSHA regulations are advised: however , OSHA regulations
also permit other type safety glasses. Consult your safety
representative.

Skin Protection: Wear rubber gloves (consult your safety
equipment supplier). To prevent repeated or prolonged skin
contact, wear impervious clothing and boots.

Respiratory Protection: If workplace exposure limits of
product or any component are exceeded (see exposure
guidelines), NIOSH/OSHA approved air supplied respirator is
advised in the absence of proper environmental control.
OSHA relations also permit other NIOSH/OSHA respirators
(negative pressure type) under specific conditions (see your
industrial hygienist). Engineering or administrative controls
should be implemented to reduce exposure.

Engineering Controls: Provide sufficient mechanical
(general and local exhaust) ventilation to maintain exposure
below level of overexposure (from known, suspected or
apparent adverse effects).