Ryobi RYI2200G - Manual (Page 11)

7 — English
SYMBOLS
fUEL WARNINg
No smoking when filling with gasoline.
Do not overfill. Full level is 1 in. below
the top of the fuel neck. Stop the en-
gine for five minutes before refueling to
avoid the heat from the muffler igniting
fuel vapors.
ENgINE LUBRIcANT WARNINg
You must add lubricant before first operating the
generator. Always check the lubricant level before
each operation. The lubricant level should always
register between the hatched areas on the dipstick.
The unit is equipped with a sensor which will auto-
matically shut off the engine if the lubricant level falls
below a safe limit.
gROUNDINg WARNINg
National Electric Code requires generator
to be grounded to an approved earth
ground.
HOT SURfAcE WARNINg
Do not touch the muffler or aluminum
cylinder of the engine. They are very HOT
and will cause severe burns. Don’t put any
flammable or combustible materials in the
direct path of the exhaust.
Product does not include ground rod or copper wire. National Electric Code requires generator to be
properly grounded to an approved earth ground. Call an electrician for local grounding requirements.
Le produit ne comprend pas de piquet de terre ou de fil en cuivre. Le code electrique americain (National
Electric Code) requiert un générateur pour une bonne mise à la terre approuvée. Appeler un électricien
pour connaître les exigences locales de mise à la terre.
El producto no incluye el alambre de cobre ni la barra de conexión a tierra. Los Reglamentos Nacionales
de Electricidad exigen que el generador esté debidamente conectado a una tierra aprobada.
Comuniquese con un electrista para todo lo relacionado con los requistos de conexión a tierra.
WARNING ADVERTENCIA AVERTISSEMENT
940513008-02
Risk of Fire. Check for any fuel overflow or leaking. Stop the engine before refueling.
DANGER PELIGRO
Risque d’incendie. Vérifier l'absence de débordement ou de fuite de carburant.
Arrêter le moteur avant de fair le plein.
Riesgo de incendio. Revise si hay algún derrame o fuga de combustible. Apague el
motor antes de poner combustible.
940974007-03
cLEARANcE WARNINg
While operating and storing, keep at least 3 feet of clearance on all sides of this product, including overhead. Allow a mini-
mum of 30 minutes of “cool down” time before storage. Heat created by muffler and exhaust gases could be hot enough
to cause serious burns and/or ignite combustible objects.
940974094-02
188 mm
24.6 mm
EDITION : A
2013.02.14
OP
Multiple
100%
Total: 2C
Illustrator (PDF)
Refer to Drawings for Dimensions
Special size +/-0.2mm
Black + Pantone 485C
Pantone
485C
Revision Changes:
1. Corrected measurement in SP.
2. Adjusted revision code and date.
Note:
1. Die cut information is noted in blue/cyan color.
2. Maximum allowable Lead content to be 90 PPM max
and Cadmium content to be 100 PPM max per TTI requirement.
3. Label must resist oil, water, and gasoline per ANSI Z535/UL 969-1991.
Flexcon 21970
with Matte P.P.
or approved alternate
material
This drawing belongs to TTi Group North America. Its contents are confidential and proprietary and shall not be
disclosed to or used by or for outside parties without TTi Group North America’s written consent.
Risk of Fire. Keep all objects at least 3
feet (91.4 cm) away from this machine.
Heat from muffler and exhaust gases
can ignite combustible objects.
Riesgo de incendio. Mantener todos los objectos a
una distancia minima de 91,4 cm (3 pies) de esta
maquina. El calor de los gases del silenciador y el
escape pueden prender gurego a objectos
combustibles.