Allen Sports 532RR - Manual

M M M Mo o o od d d de e e ellll 5 5 5 53 3 3 32 2 2 2R R R RR R R R IIIIn n n ns s s sttttrrrru u u uc c c cttttiiiio o o on n n ns s s s
English - Page 1
W W W W ARNING ARNING ARNING ARNING : : : : Bikes or rack falling in road can cause serious accidents resulting in bodily injury—do not use rack on any
vehicle on which it can not be properly mounted as described in this instruction sheet.
• Rack should only be used on vehicles with 1 1/4” or 2” receiver hitches.
• N N N N EVER EVER EVER EVER use on trailers or front of vehicles.
• Bikes must be tied to rack using tie-downs, or additional straps if necessary.
• Check periodically during use that all bolts and pins are tight, and that rack and bicycles are secure.
• Never carry more than 3 bikes (max capacity 100 LB max capacity 100 LB max capacity 100 LB max capacity 100 LB) - no tandems, mopeds, or recumbents. Car tail lights must
remain visible.
• Drive conservatively, especially over bumps. Never use off-road.
• Do not use if any part of the rack is damaged, worn, or missing. Contact R. A. Allen Co., Inc. for replacement parts.
C C C C AUTION AUTION AUTION AUTION : : : : Use Allen 532RR only in accordance with local motor
vehicle and traffic regulations.
• Install rack and load bicycles only at a safe distance away
from moving traffic.
• Make sure that all of rack and bicycles are kept at a safe dis-
tance from road and hot exhaust.
• Only operate vehicle with rack in an upright, locked position.
• Bicycles should never extend beyond sides of vehicle.
• Remove rack from car, or fold carry arms down when not in
use.
A. A. A. A. P P P P ARTS ARTS ARTS ARTS ::::
T T T T OOLS OOLS OOLS OOLS REQUIRED REQUIRED REQUIRED REQUIRED :::: 2—9/16” W RENCH & 2—3/4” W RENCH ;
OR 2—A DJUSTABLE W RENCHES
532RR B OX SHOULD CONTAIN THE
FOLLOWING ITEMS :
1 1 1 1— — — —C C C C ARRY ARRY ARRY ARRY A A A A RM RM RM RM A A A A S- S- S- S-
SEMBLY SEMBLY SEMBLY SEMBLY
1 1 1 1— — — —RR P RR P RR P RR P OST OST OST OST
1 1 1 1— — — —H H H H ARDWARE ARDWARE ARDWARE ARDWARE K K K K IT IT IT IT ,,,,
CONTAINING
2—3/8” X 2 1/2” BOLT
1—3/8” X 3” BOLT
4—3/8” L OCK N UT
1—1/2” L OCK N UT
1—1/2” N O -W OBBLE
B OLT
B. B. B. B. A A A A SSEMBLING SSEMBLING SSEMBLING SSEMBLING R R R R ACK ACK ACK ACK ::::
S S S S TEP TEP TEP TEP 1 1 1 1 S S S S TEP TEP TEP TEP 2 2 2 2
• I NSERT LOWER PORTION OF RR P OST INTO
H ITCH I NSERT SO THAT THE HOLES AT THE BOT-
TOM OF EACH PART LINE UP .
• I NSERT THE 3/8” X 3” BOLT THROUGH THE
HOLE , AND THREAD 1—3/8” LOCK NUT ONTO
THE END OF THE BOLT .
• P IVOT THE RR P OST INTO THE UPRIGHT POSI-
TION , SO THAT THE UPPER HOLES LINE UP . I N-
SERT THE QR C LIP THROUGH THESE HOLES , AND
SECURE THE WIRE RETAINER CLIP .
• T IGHTEN NUT AND BOLT FIRMLY USING TWO
WRENCHES .
H H H H ITCH ITCH ITCH ITCH IIII NSERT NSERT NSERT NSERT
RR P RR P RR P RR P OST OST OST OST
3/8” L 3/8” L 3/8” L 3/8” L OCK OCK OCK OCK
N N N N UT UT UT UT
3/8” 3/8” 3/8” 3/8” X X X X 3” 3” 3” 3”
B B B B OLT OLT OLT OLT
• I NSERT C ARRY A RM A SSEM-
BLY INTO UPPER PORTION
OF RR P OST , LINING UP
THE HOLES IN EACH PART .
• I NSERT THE 3/8” X 2 1/2”
BOLTS THROUGH EACH
HOLE , AND THREAD 1—
3/8” LOCK NUT ONTO THE
END OF THE BOLTS .
• T IGHTEN NUT AND BOLT
FIRMLY USING TWO
WRENCHES .
NOTE: NOTE: NOTE: NOTE: U PON COMPLETION ,
BOTH PARTS SHOULD BE
FIRMLY JOINED TOGETHER .
C C C C ARRY ARRY ARRY ARRY A A A A RM RM RM RM A A A A SSEMBLY SSEMBLY SSEMBLY SSEMBLY
3/8” 3/8” 3/8” 3/8” X X X X 3 3 3 3” ”” ”
B B B B OLT OLT OLT OLT
QR C QR C QR C QR C LIP LIP LIP LIP
IMPORTANT: IMPORTANT: IMPORTANT: IMPORTANT:
W HEN RACK IS IN AN
UPRIGHT POSITION ,
W IRE R ETAINER ON QR
C LIP SHOULD ALWAYS BE
IN A CLOSED POSITION
TO KEEP RACK FROM
FALLING OVER DURING
USE .
1 1 1 1— — — —H H H H ITCH ITCH ITCH ITCH IIII NSERT NSERT NSERT NSERT W W W W / / / /
FILLER FILLER FILLER FILLER PLATES PLATES PLATES PLATES
1—3/8” N O -W OBBLE
B OLT
F ILLER P LATES