Universal Remote Control (URS) UR2-211 - Manual

STEP2 Press and hold the [DEVICE]
key for 5 seconds until the
Device LED will blink once
and stays on. Continue to hold
the [DEVICE] key and press
the number key assigned to
your brand in the Quick Set-
up Code Table and release
both [DEVICE] key and the
number key to save the code.
The Device LED will blink
twice to confirm that the code
is stored.
STEP3 Point the remote control at the
component.
STEP4 Press the power button. If it
turns off, it is programmed for
your component. If it does not
turn off, use the Pre-
Programmed 3-Digit code
Method or Scanning Method.
Repeat the steps above for all
components (CBL, TV).
B. Quick Set-up Code Tables B. Quick Set-up Code Tables
C. C. Manual Programming Manual Programming
The remote control can be programmed
by entering a three-digit code number
that corresponds to particular brands
and models of equipment. The three-
digit code numbers are listed in the
code tables sections of this instruction
manual.
STEP1 Turn on the equipment that
you want the remote con-
trol to operate (Cable Box or
TV).
STEP2 Press the [DEVICE] button
and the [OK/SEL] button
simultaneously for 3 seconds.
The corresponding device
LED will turn on indicating
that it is ready to be pro-
grammed. The LED will remain
on for 30 seconds. The next
step must be entered while
the LED is on.
STEP3 Point the remote control
toward the equipment and
enter the three-digit code
number assigned to your
STEP1 Turn on the equipment that
you want the remote control
to operate (Cable Box or TV).
STEP2 Press the [DEVICE] button
and the [OK/SEL] button
simultaneously for 3 seconds.
The device LED will turn on
indicating that it is ready to
be programmed. The LED
will remain on for 30 seconds.
The next step must be enter-
ed while the LED is on.
STEP3 Press the [CH
5] or [CH6]
button one at a time or keep
it pressed. The remote will
emit a series of Power
ON/OFF code signals. Release
the [CH
5] or [CH6] button
as soon as the equipment
turns off.
*Note: You can verify that you have
selected the correct code by
pressing the [POWER]
button. The equipment
should turn back on. Then
try all of the functions on
the remote control (i.e.
volume, mute, etc.) to ensure
you have the correct code. If
any of the functions do not
operate as they should,
repeat the instructions from
STEP 3 above to continue
the Auto Search Method.
STEP4 Press the same [DEVICE]
brand from the code tables.
If there are more than one
three-digit number listed for
your brand, try one code
number at a time until your
equipment turns off.
*Note: You can verify that you have
selected the correct code by
pressing the [POWER] button.
The equipment should turn
back on. Then try all of the
functions on the remote
control (i.e. volume, mute,
etc.) to ensure you have the
correct code. If any of the
functions do not operate as
they should, repeat the
instructions from STEP 3
above using the next three
digit code number from the
brand list.
STEP4 Store the three-digit code
by pressing the same
[DEVICE] button once again.
The device LED will blink
twice to confirm that the
code has been stored.
D. Auto Search Method D. Auto Search Method
If none of the three digit code numbers
assigned to your brand of equipment
works, or the code table does not list
your brand, you can use the Auto
Search Method to find the correct
three-digit code number for your
equipment by following steps:
Button Functions
3
Programming the Remote Control
4
Macro Button
For future use
Universal Remote Control, Inc.
www.universalremote.com
OCE-0082E Rev 08 (14/03/14)
UR2-211
Operating Manual
For Easy Clicker This remote control is designed
to operate most Digital, Analog
Cable boxes, IPTV set top boxes
and TVs.
Introduction
1
Replacing Batteries
2
Before you program or operate the
remote control, you must install
two new AA alkaline batteries.
STEP1 Remove the battery com-
partment cover from the
back of your remote control.
STEP2 Check battery polarity
carefully, and install the
batteries as shown in the
illustration below.
STEP3 Replace the battery com-
partment cover.
*Note : In this section, when you are instructed to press a [DEVICE] button, that means you should press either
the CBL or TV button, depending on which device you are programming the remote to operate.
A. Quick Set-Up Method A. Quick Set-Up Method
(Refer to the Section B Quick Set-up table of codes)
STEP1 Turn on the component you want to program. To program your TV, turn on the TV.
0 PACE DTA
1 SA/CISCO, SAMSUNG, PACE DIGITAL
2 MOTOROLA DIGITAL
3 MOTOROLA DTA
4 EVOLUTION DTA
5 CISCO IPTV
6 ADB IPTV
7 TECHNICOLOR
8 AMINO 140/540 IPTV
9 MOTOROLA IPTV
Quick Number Manufacturer/Brand
CBL
0 SANYO
1 SONY
2 SAMSUNG
3 LG
4 TOSHIBA
5 PANASONIC
6 PHILIPS
7 HITACHI
8 SHARP
9 VIZIO
Quick Number Manufacturer/Brand
TV