Campbell Hausfeld SHIELDEDMETAL ARCWELDER WS0970 - Manual (Page 3)

2
1
Para or
denar r
epuestos, comuníquese con el distribuidor
más cer
cano a su domicilio
Puede escribirnos a: The Campbell Group/ Scott Fetzer Attn: Parts Department 100 Mundy Memorial Drive Mount Juliet, TN 37122 U.S.A.
Sírvase suministrarnos la siguiente información: -
Número del modelo
-
Número de Serie (de haberlo)
-
Descripción y número del repuesto según la lista de repuestos
Modelo WS0970
1
Ensamblaje del portaelectrodos- No incluye
el cordón eléctrico
WC200000AV
1
2
Pinza (No incluye el cordón)
WC100000AV
1
3
Etiqueta de seguridad
(no se muestra)
DK687500AV
1
4
Martillo/cepillo cincelador (no se muestra)
WC803000AV
1
5
Máscara de mano (no se muestra)
WC801700AV
1
6
Lentes de la máscara de mano (no se muestra)
WC801100AV
1
7
Electrodos de soldar (no se muestra)
1/16” (1,6 mm) E6013 (tubo de 0,5 lbs [227 g])
WE103501AV
+
5/64” (2 mm) E6013 (tubo de 0,5 lbs [227 g])
WE103001AV
+
1/16” (1,6 mm) E7014 (tubo de 0,5 lbs [227 g])
WE105501AV
+
5/64” (2 mm) E7014 (tubo de 0,5 lbs [227 g])
WE105001AV
+
1/16” (1,6 mm) autoencendido (tubo de 0,3 lbs [136 g])
WE110001AV
+
8
Casco de soldar (no se muestra)
Área de visión 2” x 4-1/4” (5 x 11 cm)
WT100500AV
+
Área de visión 4-1/2” x 5-1/4” (11,5 x 13 cm)
WT101000AV
+
Oscurecimiento automático
WT100600AV
+
+
Accesorios opcionales (no se incluyen con el soldador)
Ref No.
Description
Part Number
Qty
Lista de Repuestos - Modelo WS0970
Soldadora con Arcos Revestidos
●
Store electrodes in a clean, dry location with low humidity to preserve the flux coating.
●
The receptacle used for the welder must be properly grounded and the welder must be the only load on the power supply circuit. Refer to the Circuit Amps chart on page 1 for correct circuit capacity.
●
The use of an extension cord is not recommended for arc welding machines. Extension cord use will significantly degrade the performance of the welder.
Assembly
HANDSHIELD 1.
Cut detachable handle away from shield. Trim the excess plastic to remove sharp edges.
2.
Insert filter lens.
CALIFORNIA PROPOSITION 65 This product, when used for welding, produces fumes or gases which contain chemicals known to the State of California to cause birth defects (or other reproductive harm) and, in some cases, cancer (California Health & Safety Code Section 25249.5 et seq.). The power cord and other cables on this product contain chemicals, including lead, known to the State of California to cause [cancer and] birth defects or other reproductive harm. Wash hands after handling. Do not breathe fumes that are produced by the arc welding operation. These fumes are dangerous. If the welding area cannot be adequately ventilated, be sure to use an air- supplied respirator. ●
Keep the head and face out of the welding fumes.
●
Do not perform electric arc welding operations on metals that are galvanized or cadmium plated, or contain zinc, mercury, or beryllium without completing the following precautions: a.
Remove the coating from the base metal.
b.
Make sure that the welding area is well ventilated.
c.
Use an air-supplied respirator.
Extremely toxic fumes are created when these metals are heated.
The electromagnetic field that is generated during arc welding may interfere with the operation of various electrical and electronic devices such as cardiac pacemakers. Persons using such devices should consult with their physician prior to performing any electric arc welding operations. ●
Route the electrode and work cables together and secure with tape when possible.
●
Never wrap arc welder cables around the body.
●
Always position the electrode and work leads so that they are on
the
same side of the body.
!
WARNING
!
WARNING
!
WARNING
!
DANGER
3
34 Sp
Model
WS0970
●
Exposure to electromagnetic fields during welding may have other health effects which are not known.
Always be sure that the welding area
is secure and free of hazards (sparks, flames, glowing metal or slag) prior to leaving. Be sure that equipment is turned off and electrode is removed. Be sure that cables are loosely coiled and out of the way. Be sure that all metal and slag has cooled. ADDITIONAL SAFETY STANDARDS ANSI Standard Z49.1
from American
Welding Society, 550 N.W. LeJune Rd. Miami, FL 33126 Safety and Health Standards OSHA 29 CFR 1910, from Superintendent of Documents, U.S. Government Printing Office, Washington, D.C. 20402 National Electrical Code NFPA Standard 70, from National Fire Protection Association, 1 Batterymarch Park, Quincy, MA 02169 Safe Handling of Compressed Gases in Cylinders CGA Pamphlet P-1, from Compressed Gas Association, 1235 Jefferson Davis Highway, Suite 501, Arlington, VA 22202 Code for Safety in Welding and Cutting CSA Standard W117.2, from Canadian Standards Association, Standards Sales, 178 Rexdale Boulevard, Rexdale, Ontario, Canada M9W 1R3 Cutting And Welding Processes NFPA Standard 51B, from National Fire Protection Association, 1 Batterymarch Park, Quincy, MA 02169 Safe Practices For Occupational And Educational Eye And Face Protection ANSI Standard Z87.1, from American National Standards Institute, 1430 Broadway, New York, NY 10018 Refer to the Material Safety Data Sheets and the manufacturers instructions for metals, electrodes, coatings and cleaners.
Installation Location Selecting the proper location can significantly increase performance, reliability and life of the arc welder. ●
For best results locate the welder in an environment that is clean and dry. Dust and dirt in the welder retain moisture and increase wear of moving parts.
!
WARNING
www.chpower.com
Figure 2 Figure 3 Figure 4
General Safety (Continued)