Kontron AM4150 IPMI Firmware - Manual (Page 35)

AM4150 IPMI Firmware
ID 1052-5679, Rev. 1.0 Page 35
P R E L I M I N A R Y
7.1.1 Board Configuration Options
In addition to the “sconf” base configurations, there are further board configuration options which
depend on the type of the fabric interface used or the “sconf” base configuration selected. For
example, the SRIO-related board configuration is available only if SRIO interfaces are available;
the FCLKA configuration is available only when PCI Express interfaces are present. For infor-
mation on the AMC interconnection capabilities and the fabric interfaces supported for an “sconf”
base configuration, refer to the AM4150 User Guide, Chapter 2.10, AMC Interconnection.
The following table indicates the fabric interfaces available and which board configuration op-
tions can be applied to the respective “sconf” base configuration.
Table 14: Overview of Board Configuration Options
AMC PORT CONFIGURATION USING THE
U-BOOT “sconf info” BASE CONFIGURATIONS
FURTHER BOARD CONFIGURATION OPTIONS
DEPENDING ON THE BASE CONFIGURATION
“sconf”
Base
Conf.
AMC PORT
GbE
dTSEC4
SRIO
Sys.
Size
SRIO
Mode
FCLKA
PCIe
Ref.
Clock
Ports
4 - 7
Speed
Options
Ports
8 - 11
Speed
Options 0 1 2 3 4 - 7 8 - 11
0 GbE [GbE] SATA SATA /
--
SRIO
[@5.0]
SRIO
[@5.0]
port 1 /
front
small /
large
host /
agent
-- @5.0 /
@2.5
@5.0 /
@2.5
1 GbE [GbE] SATA SATA /
--
SRIO
@3.125
SRIO@
3.125
port 1 /
front
small /
large
host /
agent
-- -- --
2 GbE [GbE] SATA SATA /
--
SRIO
[@5.0]
GbE,
GbE,
[GbE],
--
port 1 /
port 10 /
front
small /
large
host /
agent
-- @5.0 /
@3.125 /
@2.5
--
3 GbE [GbE] SATA SATA /
--
PCIE
[Gen.2]
PCIE
[Gen.2]
port 1 /
front
-- -- auto / in /
out / local
@5.0 /
@2.5
@5.0 /
@2.5
4 GbE [GbE] SATA SATA /
--
PCIE
[Gen.2]
GbE,
GbE,
[GbE],
--
port 1 /
port 10 /
front
-- -- auto / in /
out / local
@5.0 /
@2.5
--
5 GbE [GbE] SATA SATA /
--
PCIE
[Gen.2]
PCIE,
GbE,
[GbE],
--
port 1 /
port 10 /
front
-- -- auto / in /
out / local
@5.0 /
@2.5
--
Note ...
Optional configuration parameters are denoted by the use of square brackets.
For example, [GbE] indicates that dTSEC4 used can be redirected to the front
panel connector J2 (GbE B) or optionally to AMC port 10 for configurations
which provide GbE interfaces in the Fat Pipes Region, port 8 or port 9.
Note ...
There are two SATA ports available on the AM4150. The first SATA port is
routed to the AMC port 2. The second SATA port is routed either to AMC port 3
or to the SATA Flash module.