Environmental Water Systems CS-BB-FUGAC200A-1 - Manual (Page 2)

ALL FILTRATION PRODUCT PROUDLY MADE & ASSEMBLED IN THE USA
www.ewswater.com O: 702.256.8182; M-F 8:30am-4:30pm PST E: [email protected]
EWS
FILTER SPECIFICATIONS:
Pre-Filter: BB-PRESED-50-SW
Construction: 100 % Pure Polypropylene Fibers
Dimensions: 4 1/2 in. x 20 in. (11.4 cm x 51.0 cm)
Micron Rating: 50 µm Nominal
Initial Pressure Change: 1.00 psid @10.0 GPM
Fits all Standard 20 in. Housings
Meets FDA Requirements for food and beverage contact.
Filter: BB-GACB-10-RFA
Vibration Packed Radial Flow Granular Activated Carbon Block
Dimensions: 4 1/2 in. x 20 in. (11.4 X 51.0 cm)
Micron Rating: 20 µm Nominal
Initial Pressure Change: 3.00 psid @7.0 GPM
Chlorine Reduction: 40,000 Gal. @ 7.0 GPM based
on 2ppm chlorine with greater than 90% reduction
Fits all Standard 20 in. Housings
Cartridge is Tested and Certified by International
ANSI/NSF Standards 42 and 61 - Conforms to requirements.
System Weight: 29 lbs./ 13.18 Kgs.
System Size: 8 5/8 in. W x 15 3/8 in. L x 26 1/4 in. H / 21.6 cm x 38.8 cm x 66.5 cm
Min/Max Water Temperature: 40º / 100 ºF - 4.4 / 37.8 ºC
Max Water Pressure for 20” Housings: 100 PSI / 6.2 Bar
Initial Pressure Change of Vessel without Filters: 1.00 psid @15.0 GPM
WARNING: It is recommended that working pressure does not exceed or surge above 75 PSI and that a working PRV be installed to
control high household pressure and/or pressures surges.
CS-BB-FUGAC200A-1 Housing Inlet/Outlet Size: 1” Flow Rate : <10.0 GPM / 37.85 LPM
Designed system flow rates to insure proper filtration tolerances.
SHIPPING INFORMATION: Carton Size.:16 in. W x 10 in. L x 28 in. H
**Up to one year or as needed, based on local water conditions, usage and flow rates. Diminished flow rate or filtration issues
indicates cartridge change needed. Application for known municipally treated or well water of known quality. All waranties and
application requirements apply. For other performance requirements or applications, other models are available.
Pictured:
CS-BB-FUGAC200A-1 with Spanner Wrench
and filter cartridges,
BB-PRESED-50-SW and BB-GACB-10-RFA
Technical Information: CS-BB-FUGAC200A-1
REPLACEMENT FILTERS
Part No. Description Replacement Time**
BB-PRESED-50-SW 50 Micron String Wound Sediment Cartridge Up to a Year
BB-GACB-10-RFA 20” Carbon Block Radial Flow Cartridge Up to a Year
SET-UP, INSTALLATION OF UNIT & BYPASS AND START-UP:
(1) Shut off main water supply.
(2) Install at main, point of entry or designated water line using proper plumber supplied pipe, fittings,
unions and ball (shut-off) valves to the inlet, outlet and bypass of the unit.
(3) Install a bypass with proper ball valves before inlet and after outlet of unit and on bypassed line. (Note) Make
sure unions are installed between the inlet and outlet of the unit and the installed ball valves for future unit servicing.
(4) Once unit installation and bypass is complete, open main water supply.
(5) Slowly open (less than 1/2 regular flow rate or less than 5 gpm) inlet of unit and close bypass. Keep outlet of
unit closed and allow unit to fill slowly. Check unit at inlet connections, housings, bracket and housing connections.
(6) Once filled, open inlet and outlet of unit completely. Check all connections.
(7) Flush unit of carbon fines. Find nearest faucet to the unit, remove aerator or any restriction, and open cold side
only. Allow carbon fines to flush through faucet until water runs clear. Open all faucets to clear air in lines.
(8) Affix a plumber service label or card on unit and record installation date. Leave this booklet and warranty booklet
with unit and/or consumer. Replace filters up to one year after initial installation and/or at regular or needed intervals.**