Environmental Water Systems BB 11/2” - Manual (Page 2)

ALL FILTRATION PRODUCT PROUDLY MADE & ASSEMBLED IN THE USA
www.ewswater.com O: 702.256.8182; M-F 8:30am-4:30pm PST E: [email protected]
EWS
FILTER SPECIFICATIONS:
Pre-Filter: BB-081
Construction: 100 % Pure Polypropylene Fibers
Dimensions: 4 1/2 in. x 20 in. (11.4 cm x 51.0 cm)
Micron Rating: 5 µm Nominal
Initial Pressure Change: 1.00 psid @10.0 GPM
Fits all Standard 20 in. Housings
Meets FDA Requirements for food and beverage contact.
Fits all Standard 20 in. Housings
Cartridge is Tested and Certified by International
ANSI/NSF Standards 61 - Conforms to requirements.
System Weight: 10 lbs./ 4.54 Kgs.
System Size: 8 5/8 in. W x 7 1/2 in. L x 26 1/4 in. H / 21.6 cm x 19.05 cm x 66.5 cm
Min/Max Water Temperature: 40º / 100 ºF - 4.4 / 37.8 ºC
Max Water Pressure for 20” Housings: 100 PSI / 6.2 Bar
Initial Pressure Change of Vessel without Filters: 1.00 psid @15.0 GPM
WARNING: It is recommended that working pressure does not exceed or surge above
75 PSI and that a working PRV be installed to control high household pressure and/or
pressures surges.
BB 1” SETUP Housing Inlet/Outlet Size: 1” <10.0 GPM / 37.85 LPM
BB 11/2” SETUP Housing Inlet/Outlet Size: 11/2” <20.0 GPM / 75.7 LPM
Designed system flow rates to insure proper filtration tolerances.
SHIPPING INFORMATION: Carton Size.:11 in. W x 11 in. L x 28 in. H
**Up to one year or as needed, based on local water conditions, usage and flow rates. Diminished flow rate or filtration issues
indicates cartridge change needed. Application for known municipally treated or well water of known quality. All waranties and
application requirements apply. For other performance requirements or applications, other models are available.
Pictured:
Schematic BB 1” SETUP
Technical Information: BB SETUP 1” or 11/2”
REPLACEMENT FILTERS
Part No. Description Replacement Time**
BB-081 5 Micron Sediment Cartridge Up to a Year
SET-UP, INSTALLATION OF UNIT & BYPASS AND START-UP:
(1) Shut off main water supply.
(2) Install at main, point of entry or designated water line using proper plumber supplied pipe, fittings,
unions and ball (shut-off) valves to the inlet, outlet and bypass of the unit.
(3) Install a bypass with proper ball valves before inlet and after outlet of unit and on bypassed line. (Note) Make
sure unions are installed between the inlet and outlet of the unit and the installed ball valves for future unit servicing.
(4) Once unit installation and bypass is complete, open main water supply.
(5) Slowly open (less than 1/2 regular flow rate or less than 5 gpm) inlet of unit and close bypass. Keep outlet of
unit closed and allow unit to fill slowly. Check unit at inlet connections, housings, bracket and housing connections.
(6) Once filled, open inlet and outlet of unit completely. Check all connections.
(7) Flush unit and lines of any debris. Find nearest faucet to the unit, remove aerator or any restriction, and open
cold side only. Flush through faucet until water runs clear. Open all faucets to clear air in lines.
(8) Affix a plumber service label or card on unit and record installation date. Leave this booklet and warranty booklet
with unit and/or consumer. Replace filters up to one year after initial installation and/or at regular or needed intervals.**