Main components, Dear customer, Rar-480 – Dyras RAR-480 User Manual

Page 4

RAR-480

Storing the appliance in cold or frosty environment may cause:

- damage to the plastic and rubber components; if they become fragile,

this may result in a safety risk.

- oxidation resulting from condensation, and corrosion of the metal components.

Direct and indirect heat (e.g. being too close to an oven or a heating appliance) can cause:

- damage, deformation, softening or melting of plastic or rubber parts and casing elements, or

deterioration of electrical insulation.

Following the operating instructions and avoiding any of the conditions listed above will help you
increase the lifespan of the appliance. The manufacturer is not responsible if the appliance is stored
inappropriately or contrary to these instructions. You are recommended to have the appliance
serviced regularly by an authorised engineer to keep it working for as long as possible.

Please respect the environment when the appliance reaches the end of its life. Electrical products
must not be disposed of with other residential waste because they can damage the natural world
and may be hazardous to human health. You should dispose of the appliance at an appropriate
recycling site or by using a collection service that specialises in electrical appliances.

You may wish to contact the retailer or the manufacturer if you are unable to find convenient local
recycling facilities as they have some legal responsibilities for recycling electrical products.

Please keep this instruction manual. If you give the appliance to anyone else, you must give them
this instruction manual, too!

MAIN COMPONENTS

1. Difuzér
2. Concentrator attachment
3. Handle
4. Three way air flow regulating power switch (0/1/2)
5. Cool shot switch (COOL)
6. Hanging loop
7. Power cable

become clogged with lint for some reason, you have to clean them (e.g. with a Hoover or brush) otherwise
overheating could occur and the thermal release will turn the appliance off.

•

You must not disassemble the appliance, remove its cover or to try to repair it. Ignoring this advice could
cause a serious accident. There are no parts in the appliance that can be repaired at home or used for any
other purpose. Never operate the appliance with a damaged mains cable or connector. Do not use the
appliance if it fails to work normally or if it has been dropped or damaged. If the appliance becomes faulty
for any reason or if any moisture is allowed inside, take it to an authorised service engineer for checking
and repair. Only service engineers who have been trained and approved should repair the appliance. The
manufacturer cannot take any responsibility for unauthorised repairs or for any circumstances resulting from
not following the instructions.

Dear Customer,

All electrical and mechanical equipment needs to be cared for appropriately. It’s important to
note that using or storing the appliance in certain conditions may adversely affect its lifespan and
functionality. Always protect the appliance from the conditions listed below.

Using or storing the appliance in a wet, humid or damp environment can cause:

- deterioration and premature aging of the cover and electric insulation of the appliance,
- premature wearing and aging of the plastic and rubber components,
- rust and corrosion affecting electrical components and metal parts.

Dust covered air suction grille at the rear, front grille or blower, clogging with dust or hair, failure of
cleaning may cause:

- premature wear and tear of revolving, moving parts,
- electric overload, overheating,
- operation of the in built thermal release during use due to overheating caused by insufficient

ventilation,

- increased noise emission.

Attention! In the absence of cleaning the lint coming into contact with the heating filament could
catch fire, this could couse an accident and fire hazard.

The effects of direct sunlight on the appliance can include:

- accelerated deterioration of the appliance casing and its plastic and rubber components,

damage to strength and other structural features. The appliance’s surface may become porous
and fragile, which may result in a safety risk.

Continuous heavy duty use may cause:

- premature structural wear and tear of the electro-motor due to the excessive use,
- premature amortization, blow out of the filament,
- increase noise emission,
- material fatigue, the local overheating of electric and frictional mechanical elements.

User'sManual for RAR-480.indd 6-7

2011.02.08. 19:11:57