Cuddeback C1000 - Manual (Page 8)

Longest Battery Life Fastest Trigger Time
Page 15 of 37
use a small tweezers to access the jumper. If you lose the jumper your
Cuddeback will still function properly with the sensitivity set to standard. If you
are getting false detections lower the sensitivity using the jumper or software
menu.
The built in strobe flash has an effective range of about 30 feet. To assure night
images are properly exposed we recommend aiming Cuddeback at a tree 30 to
40 feet away. This will limit Cuddeback’s detection zone to the range of the
camera flash and camera lens. Best images will be taken when the animal is 10
to 15 feet from the Cuddeback.
INSTALLING CUDDEBACK IN THE FIELD
We recommend mounting Cuddeback to the largest tree in the area, about 10
feet from where you expect the animal to appear. Place Cuddeback about 3 to 4
feet off the ground, aiming slightly down. You can use Cuddeback’s Test
Mode to verify the detection distance.
We strongly recommend using the supplied Torx
® screw to secure Cuddeback to
a tree. You will need a #25 Torx screwdriver. This assures solid mounting and
you will never have to worry about a bear, deer, or vandal knocking Cuddeback
off the tree. In addition, the supplied security cable can also be used. We also
recommend using a padlock to secure the battery cover – even if you are on
private property. This will assure that nobody tampers with your Cuddeback
Digital Camera.
! WE STRONGLY RECOMMEND THAT YOU
ONLY USE THE TORX SCREW SUPPLIED.
!
Using a Torx screw eliminates the possibility of stripping the head. A Phillips
head or slotted head screw is very likely to strip and prevent you from removing
Cuddeback from the tree.
Note: if you do not use the security cable you should still attach the
supplied eye-bolt and wing nut to prevent insects from entering
Cuddeback.
Note: if you do not use the Torx screw, install the supplied Phillips-head
screw to prevent insects from entering Cuddeback.
FIELD CHECKING CUDDEBACK
Longest Battery Life Fastest Trigger Time
Page 16 of 37
There are two methods you can use to field check your Cuddeback camera.
Using the a-switch method as described next, or you can follow this method.
1) To check Cuddeback remove the padlock (if installed), loosen the thumb
screw, and remove the battery cover.
2) Press (C KEY) to suspend Live Camera mode. The owner name (default
is Non Typical, Inc) will scroll across the LCD. You can skip this by
pressing the (C KEY). (This text can be changed, refer to the TheftStop
section in the Advanced Mode instructions).
3) If you programmed a lock password, you will be required to enter it to
access the menu systems. If you fail to enter the correct password,
Cuddeback will stop operating.
4) You should press the (M KEY) to determine if any images are saved.
5) If you have images taken, you can either 1) exchange the memory card to
view your images at home, or 2) attach a portable TV or camcorder to view
images.
6) We also recommend checking the battery level and free memory space (you
must be using Advanced Mode to do this).
7) You may want to archive the images to save time viewing images the next
time you check Cuddeback (in Advanced Mode only).
8) When you are finished you can 1) attach the battery cover and leave the
area; Cuddeback will automatically enter Live Camera mode within ten
minutes, or 2) activate Live Camera mode, replace the battery cover, and
leave the area.
9) If you want to move Cuddeback to a new location, we recommend
disarming Cuddeback to prevent erroneous images from being taken during
storage and movement.
THE A-SWITCH
Cuddeback’s a-switch (short for air-switch) allows you to determine how may
images Cuddeback has taken without opening the enclosure.
How to Activate the A-Switch
The ambient light level is the small center hole on the Cuddeback enclosure. It
is surrounded by a small ring that allows you to recognize it by feel. To use the
a-switch follow these steps:
1) Place your finger tightly over the a-switch opening for at least 9 seconds.
Observe the LED indicator as you do this.
2) The LED will illuminate for 1 second after the light is blocked for 9
seconds.
3) When the LED goes OFF immediately remove your finger. You must
remove your finger within ½ second of the light going off for the a-switch
to be recognized.