Code 3 Zenith - Manual

SOLID COLOR:
INPUT VOLTAGE ........................10 to 30 Volts DC.
INPUT CURRENT .......................1.25A @ 12.8V, 0.6A @ 25.6V
LIGHT OUTPUT ...........................AMBER: 358+ LUMENS
BLUE: 240+ LUMENS
GREEN: 312+ LUMENS
RED: 358+ LUMENS
CLEAR, PURPLE: 1100+ LUMENS
SPLIT COLOR:
INPUT VOLTAGE .........................10 to 30 Volts DC.
INPUT CURRENT .......................0.6A @ 12.8V, 0.3A @ 25.6V
LIGHT OUTPUT ...........................AMBER: 180+ LUMENS
(For each 3 LED group) BLUE: 120+ LUMENS
GREEN: 104+ LUMENS
RED: 180+ LUMENS
CLEAR: 550+ LUMENS
CABLE LENGTH ..........................9 FT.
LED ELEMENTS ..........................6
FLASH PATTERNS ......................16 (8 Standard, 8 optional cycle)
MAX NUMBER OF
SYNCHRONIZED HEADS ...........64
WARRANTY PERIOD ..................5 YEARS
TECHNICAL SPECIFICATIONS
DIMENSIONS
ITEMS INCLUDED
(1) HIDE-A-LED™ HEAD WITH INTEGRATED HEATSINK,
BUILT IN POWER MODULE
AND 9’ CABLE.
(1) MOUNTING GASKET
(2) #6 X 1/2” STAINLESS STEEL
MOUNTING SCREWS
INSTALLATION GUIDE
MOUNTING
Drill a 1” diameter hole in the reflector of the lens assembly.
A 1” hole saw is typically used. The HIDE-A-LED™ may be used as a
template to mark the location of the two screw holes. The Z1000 may
be mounted in either the back surface, bottom or sides of a reflector.
Drill pilot holes with a 7/64” drill bit. Install the HIDE-A-LED™ into the
lens assembly using the supplied gasket and screws. If the mount-
ing surface is curved additional sealing may be necessary. Use RTV
Silicone sealant if needed.
STRAP THE WATERPROOF
POWER MODULE TO THE BODY
OF THE VEHICLE AWAY FROM
ANY HIGH HEAT SOURCES.
! HOT !
GASKET
REFLECTOR
DO NOT DRILL HOLES THROUGH THE POWER MODULE!
ELECTRICAL CONNECTIONS
The cable on the HIDE-A-LED™ was made long enough to run across
the front or the rear of a vehicle. Trim the cable shorter if needed. The
wiring diagram on page 2 shows a typical install.
RED: +V
Connect to +V through an ON/OFF switch.
The use of a fuse located close to the voltage source is recommended.
Size the fuse according to the number of heads used in the system.
18AWG or larger wire is recommended.
BLACK: - GROUND
Connect to - GROUND vehicle chassis.
18AWG or larger wire is recommended.
BLUE: Flash pattern SYNC and SELECTION wire.
If you wish to have all the LED heads synchronize
their flash timings and patterns with each other then all the BLUE wires
must be connected together (64 Heads Maximum).
The BLUE wire is also used to select the flash pattern.
Touch the BLUE wire to +V to select the next pattern in the FLASH
PATTERN LIST. The BLUE wire can also be run to a momentary
push-button located on the dashboard to allow the flash pattern to be
changed when desired.
Note: Do not connect the BLUE wire to - Ground.
It will disrupt the flash pattern sync signal.
PAGE 1 920-9120-00 REV. A
Z1000
LED HEAD POWER
MODULE
1” HOLE
7/64” PILOT
HOLES
SPLIT COLOR
0.94"
1.27"
1.50"
1.28"
0.96"
0.48"
4.83"
0.92"
CABLE
1.94"
THE HEATSINK WILL BE HOT AFTER RUNNING
FOR AN EXTENDED PERIOD. DO NOT TOUCH.
IT WILL NOT MELT ANY OF THE PLASTIC
PARTS OF THE LENS ASSEMBLY.
THE Z1000 HAS AN INTEGRATED HEATSINK WHICH MUST BE
USED TO MAINTAIN A SAFE OPERATING TEMPERATURE.
! THE HEATSINK MUST NOT BE REMOVED !
THE HEATSINK CAN BE BENT INTO ANY SHAPE NEEDED TO FIT
THE SPACE AVAILABLE FOR THE APPLICATION.
SOLID COLOR
SCREWS
TIP: APPLY RTV SILICONE
TO THE SCREWS TO SEAL
THE THREADS.
INTEGRATED
HEATSINK
833 W. Diamond St Boise, Idaho 83705
TEL: 800-635-5900 www.eccogroup.com