Code 3 SuperVisor with TriCore for 2011 Ford Explorer - Manual (Page 3)

3
Installation and Mounting Instructions
Step 1 Remove the plastic covers from the driver and passenger outer sun visor pivot brackets (see Figures 1 & 2). Remove the
(2) small Torx screws as shown in Figures 3 and 4 from each pivot bracket. Pull the visor pivot brackets down from the headliner and
carefully allow the sun visors to hang by the vehicle's attached vanity mirror light wires.
Step 2 Unscrew the single Torx screw holding each of the vehicle's (2) inner visor clips in place as shown in Figure 5.
Step 3 Attach the vehicle's inner visor clips to the SuperVisor Inner Mounting Brackets as shown in Figure 6. Thread each of the
vehicles Torx screws you removed in step 2 above all the way up into the vehicle's plastic inner visor clip (this makes it easier to
see the end of the screw so you can thread the screw into it's hole in the headliner). Position the SuperVisor Inner Mounting
Brackets up to the headliner as shown in figure 7 page 4 and loosely thread the screws into the screw hole in the vehicle's headliner.
Tighten the screws until the brackets are within about 1/8" of the headliner. Do not fully tighten the screws at this time.
Step 4 Attach the vehicle's plastic outer visor pivot brackets to the supplied SuperVisor Outer Mounting Brackets noting the differ-
ence between the passenger and driver side and thread the (2) Torx screws as shown in Figure 8 on page 4 (Drivers Side Shown).
Tighten the screws until the brackets are within about 1/8" of the headliner. Do not fully tighten the screws at this time.
Step 5
Route the SuperVisor's cable to the desired side of the vehicle and out the end of the SuperVisor's Outer Panel. Make sure
the cable will not interfere with the vehicle's headliner and windshield as you position the SuperVisor up to the headliner in front of the
SuperVisor Inner and Outer Mounting Brackets as shown in Figure 9 page 4.
Step 6 Line up the slots in the SuperVisor Inner Mounting Brackets with the threaded holes in the SuperVisor, and thread the sup-
plied 1/4"-20 screws and internal tooth lock washers through the slots and into the SuperVisor's Outer Panel (see Figure 10 page 4).
Step 7 Line up the slots in the SuperVisor's Outer Mounting Brackets with the threaded holes in the SuperVisor, and Thread the
supplied 1/4"-20 screws and internal tooth lock washers through the slot in the SuperVisor's Outer Mounting Brackets and into the
SuperVisor's Outer Panel (see Figure 11 page 4).
Step 8
Make sure the SuperVisor is exactly centered in the vehicle and tighten all (6) of the vehicle's the Torx screws in the SuperVi-
sor's Inner and Outer Mounting Brackets (Inner Brackets see Figure 12 page 4 - Outer Brackets see Figure 13 page 4).
Step 9
While pushing the SuperVisor very tightly up against the headliner, tighten the (2) 1/4"-20 SuperVisor Inner Mounting Bracket
screws as shown in Figure 14 then again while pushing the SuperVisor very tightly up against the headliner, tighten the (2) 1/4"-20
SuperVisor Outer Mounting Bracket screws as shown in Figure 15 page 4. Note: It is best to have an assistant push up on the
SuperVisor while you tighten the screw to assure that it is tight against the vehicle's headliner.
Step 10 Replace the plastic covers on the driver and passenger outer sun visor pivot brackets (see Figure 16 page 4).
FIgURE 1 FIgURE 2 FIgURE 3
FIgURE 4 FIgURE 5 FIgURE 6