Clarion pro audio vrx 630 - Manual (Page 30)

34
VRX630
English
Owner
’s manual
4. Operate the JOYSTICK ¡ rightward or left-
ward to select “BALANCE” or “FADER”.
5. Operate the JOYSTICK ¡ upward or down-
ward to make an adjustment.
6. Operate the JOYSTICK ¡ rightward or left-
ward to move the cursor to “MENU”, and
press the ENT at the center of the JOY-
STICK
¡ to return to the AUDIO-MODE dis-
play.
Standard mode/G.EQ
operations
Note:
• The adjustment made in standard mode is not re-
flected in the adjustment in professional mode. Re-
spectively, the adjustment made in professional
mode is not reflected in the adjustment in standard
mode.
G.EQ effect ON/OFF
* The factory default setting is “ON”.
1. Press the A-M button & to show the AUDIO-
MODE display.
2. Operate the JOYSTICK ¡ upward or down-
ward to select “EQ ON/OFF”. “ON” and “OFF”
items are displayed in the menu bar.
3. Operate the JOYSTICK ¡ rightward or left-
ward to select “ON” or “OFF” and press the
ENT at the center of the JOYSTICK
¡ to set
it.
4. After the setting, press the A-M button &
again to return to the STANDARD display.
Note:
• If the G.EQ effect is set to OFF, the adjustment made
in “G.EQ operations” is not reflected in the music
source.
Calling G.EQ BASIC Pattern/USER
Pattern
1. Press the A-M button & to show the AUDIO-
MODE display.
2. Operate the JOYSTICK ¡ upward or down-
ward to select “EQ MODE”. “BASIC” and
“USER” items are displayed in the menu bar.
3. Operate the JOYSTICK ¡ rightward or left-
ward to select the item thus called, and press
the ENT at the center of the JOYSTICK
¡ to
show BASIC pattern selecting display or
USER pattern selection/memory display.
4. In the Pattern selecting display, operate the
JOYSTICK ¡ rightward or leftward to se-
lect P1 to P6, and press the ENT at the
center of the JOYSTICK
¡ to call corre-
sponding G.EQ pattern. In this display,
pressing the No. button in correspondence
to the preset button
# can also call the
G.EQ pattern.
∗
After selecting P1 to P6 by the JOYSTICK
¡ , press ENT at the center of the JOY-
STICK ¡ for 2 seconds or longer to copy the
selected pattern to the USER pattern.
∗
Operate the JOYSTICK ¡ rightward or left-
ward to select “EDIT”, and press the ENT at
the center of the JOYSTICK
¡ to show G.EQ
adjusting display, in which the properties of
currently selected pattern can be adjusted.
∗
By pressing the BND button % in BASIC
pattern selecting display or USER pattern
selection/memory display you can switch be-
tween the two patterns, BASIC and USER.
5. Operate the JOYSTICK ¡ rightward or left-
ward to select “MENU”, and press the ENT
at the center of the JOYSTICK
¡ to return
to the AUDIO-MODE display.
Setting and storing G.EQ Proper-
ties/Memory into USER Pattern
1. Repeat the steps 1 to 3 of the previous
procedure (Calling G.EQ BASIC Pattern/
USER Pattern) to show BASIC pattern se-
lecting display or USER pattern selection/
memory display.
2. Operate the JOYSTICK ¡ leftward and
rightward to select “EDIT”, and press the
ENT at the center of the JOYSTICK
¡ to
show the G.EQ adjusting display.
3. When some frequency to be adjusted is se-
lected by operating the JOYSTICK ¡ right-
ward or leftward in the G.EQ adjusting dis-
play, a gain setting value at the selected fre-
quency is displayed.
4. Operate the JOYSTICK ¡ upward or
downward to adjust the G.EQ GAIN.
∗
By pressing the preset buttons # once in the
G.EQ adjusting display, the setting value for
currently stored USER pattern is obtained.
5. After making adjustments to a desired pat-
tern by repeating the operations of items 3
and 4, operate the JOYSTICK
¡ rightward
or leftward to move the cursor to “RTN”,
and press the ENT at the center of the JOY-
STICK
¡ to change over to the BASIC/
USER pattern selection/memory display.
DSP operations