Before each use, Cleaning system maintenance, Check and clean inlet screen – Craftsman 580.768040 User Manual
Page 11: Check high pressure hose, Check chemical reservoirs, Check gun and wand, Check in-line filter, Purge pump of air and contaminants, Nozzie maintenance
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".

BEFORE EACH USE
•
Check water inlet screen for damage.
•
Check high pressure hose for leaks.
•
Check chemical tanks and filters for damage.
•
Check gun and wand assembly for leaks.
•
Purge pump of air and contaminants.
•
Check engine oil level.
CLEANING SYSTEM MAINTENANCE
Check and Clean Inlet Screen
Examine garden hose inlet screen. Clean if it is
clogged or replace if it is tom.
Check High Pressure Hose
High pressure hose can develop leaks from wear,
kinking, or abuse. Inspect hose each time before using
it. Check for cuts, leaks, abrasions, bulging of cover,
or damage or movement of couplings. If any of these
conditions exist, replace hose immediately.
A
DANGER! Never repair a high pressure hose.
Replace with hose that meets the minimum
pressure rating of your cleaning system
Check Chemical Reservoirs
Tank covers should snap cleanly onto tank. Ensure
chemical labels correctly identify tank contents.
Ensure that the System Rinse tank is filled with clean
water. Ensure that Dial-A-Cleaner™ selector knob
rotates freely between each [wsition. Examine the
tanks and replace if the filter is clogged
Check Gun and Wand
Examine hose connection to gun and make sure it is
secure. Test trigger by pressing it and making sure it
springs back into place when you release it. Put safety
iatch in UP position and test trigger. You should not be
able to press trigger. Replace gun immediately if it
falls any of these tests.
Check In-Line Filter
Refer to the illustration below and service the in-line
filter if it becomes clogged, as follows:
In-line Filter
Lance
O-ring
1. Detach gun and lance from high pressure hose.
Detach lance from gun and remove o-ring and
screen from lance. Flush the screen, gun, and
lance with clean water to clear debris.
2. If the screen Is damaged, the o-ring kit contains a
replacement in-line filter screen and an o-ring. If
undamaged, reuse screen.
3. Place the in-line filter screen into the threaded end
of the lance. Direction does not matter. Push the
screen in with the eraser end of a pencil until it
rests flat at the bottom of the opening. Take care to
not bend the screen.
4. Place the o-ring into the recess. Push the o-ring
snugly against the in-line filter screen.
5. Assemble the lance to the spray gun, as described
earlier in this manual.
Purge Pump of Air and Contaminants
To remove the air from the pump, follow these
steps: .
Set up the cleaning system as described in the
ASSEMBLY section and connect the water supply.
Remove the wand extension from the gun.
Pull the trigger on the gun and hold until a steady
stream of water appears.
To remove the cx)ntaminants from the pump,
ollow these steps:
Set up the cleaning system as described in the
ASSEMBLY section, and connect the water supply.
Remove the nozzle attachment from the gun.
Start the engine according to instmctions in
OPERATION section.
Pull the trigger on the gun and hold.
When the water supply is steady and constant,
engage the safety latch and refasten the nozzle
attachment.
Nozzie Maintenance
If the nozzle becomes restricted or clogged with
foreign materials, such as did, excessive pump
pressure may develop. A partially clogged nozzle can
cause a pulsing condition during use. This generally is
not a pump related problem, but rather a clogged or
partially restricted'hozzle.
If the nozzle becomes clogged or partially restricted,
immediately clean the nozzle with the kit included with
your cleaning system by following these Instmctions:
• 'Shut off the engine and turn off the water supply.
•
Separate the wand from the gun.
•
Rgtate to stream setting.
•
Remove nozzle from the end of the wand using a
2mm or 5/64 alien wrench.
• Use the wire included in the kit or a small paper
clip to free the foreign materials clogging or
restricting the nozzle.
11