Craftsman 247.776360 - Manual (Page 4)

SAFE OPERATION PRACTICE
J
Operation
1. Do not put hands and feet near rotating parts or in the feeding chambers
and discharge opening. Contact with the rotating impeiier can amputate
fingers, hands, and feet.
2. Before starting the machine, make sure the chipper chute, feed intake, and
cutting chamber are empty and free of all debris.
3. Thoroughly inspect all material to be shredded and remove any metai,
rocks, bottles, cans, or other foreign objects which could cause personal
injury or damage to the machine.
4. If the impeller strikes a foreign object or if your machine should start
making an unusual noise or vibration, immediately shut the engine off.
Allow the impeiier to come to a complete stop. Disconnect the spark plug
wire, ground it against the engine and perform the following steps:
a. inspect for damage.
b. Repair or replace any damaged parts.
c. Check for any loose parts and tighten to assure continued safe opera­
tion.
5.
Do not allow an accumulation of processed material to build up in the
discharge area. This can prevent proper discharge and result in kickback
of material through the feed opening,
6. Do not attempt to shred or chip material larger than specified on the
machine or in this manual. Personal injury or machine damage could
result.
7. Never attempt to unciog either the feed intake or discharge opening while
the engine is running. Shut the engine off, wait until all moving parts have
stopped, disconnect the spark plug wire and ground it against the engine
before clearing debris.
8. Never operate without vacuum bag and discharge chute properly attached
to the machine. Never empty or change vacuum bag while the engine is
running. Zippered end of vacuum bag must be kept closed at all times
during operation.
9. Never operate without either the inlet nozzle or opfionai hose attachment
property attached to the machine. Never attempt to attach or change either
attachment while the engine is running.
10. Keep all guards, deflectors and safety devices in place and operating
properly.
11. Keep your face and body back and to the side of the chipper chute white
feeding material into the machine to avoid accidentai kickback injuries.
12. Never operate this machine without good visibility or light. Always be sure
of your footing and keep a firm hold on the handies.
13. Do not operate this machine on a grave! surface.
14. Do not operate this machine while under the influence of aicohoi or drugs.
15. Muffler and engine become hot and can cause a burn. Do not touch.
16. Never pick up or carry machine while the engine is running.
Maintenance & Storage
1. Never tamper with safety devices. Check their proper operation reguiariy.
2. Check bolts and screws for proper tightness at frequent intervals to keep
the machine in safe working condition. Also, visually inspect machine for
any damage and repair, if needed,
3. Before cleaning, repairing, or inspecting, stop the engine and make certain
the impeiier and aii moving parts have stopped. Disconnect the spark plug
wire and ground it against the engine to prevent unintended starting.
4. Do not change the engine governor settings or overspeed the engine. The
governor controls the maximum safe operating speed of the engine,
5. Maintain or replace safety and instruction labels, as necessary.
6. Follow this manual for safe loading, unloading, transporting, and storage
of this machine.
7. Never store the machine or fuel container inside where there is an open
flame, spark or pilot light such as a water heater, furnace, ciothes dryer,
etc.
8. Always refer to the operator’s manual for proper instructions on off-season
storage.
9. If the fuel tank has to be drained, do this outdoors.
10. Observe proper disposal laws and regulations for gas, oil, etc. to protect
the environment.
Do not modify engine
To avoid serious injury or death, do not modify engine in any way.Tampering
with the governor setting can lead to a runaway engine and cause it to operate
at unsafe speeds. Never tamper with factory setting of engine governor.
Notice regarding Emissions
Engines which are certified to comply with California and federal ERA emission
regulations for SORE (Smaii Off Road Equipment) are certified to operate on
regular unleaded gasoline, and may include the following emission control sys­
tems: Engine Modification (EM) and Three Way Catalyst (TWC) if so equipped.
Your Responsibility
Restrict the use of this power machine to persons who read, understand and
follow the warnings and instructions in this manual and on the machine.