Cleaning, Precautions, Specifications – Sony CPJ-100 User Manual
Page 6: Location of controls, Troubleshooting
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
English
Cleaning
Be sure to turn off the power and
disconnect the AC plug from a wall
outlet.
Cleaning the unit
Clean the unit with a soft, dry cloth. If the
dirt IS excessive, wipe it off with a soft
cloth lightly moistened with a mild
detergent solution and wipe with a soft
dry cloth.
Do not apply any type of solvent which
may damage the finish.
Cleaning the lens
Clean the surface of the lens with a
blower brush. Do not rub with a doth.
The lens cleaning tissue papers are
recommended.
Cleaning the Filter
(S
m
Illustration B.)
If there is excessive dust on the air intake,
the temperature in the unit increases,
"TEMP" appears on the screen and the
unit does not work.
1
Point the lens upward.
2
Pull the filter out
Put your finger nail or a coin into the
groove on the filter and pull down.
3
Wash the filter sponge.
Remove it from the fUto-. Wash with
water or a mild detergent solution and
then rinse with water. After washing,
allow it to dry completely.
If dirt remains or danuge occurs to the
filter sponge, please consult your
nearest Sony dealer.
4
Install the filter sponge to the
filter.
Put it into each retainer on the filter.
5
Install the filter to the unit
Precautions
• Operate the unit only on 120 V AC, 60
Hz, or it may cause a malfunction.
* Do not place the unit in a location
where it is:
• near fire
- possible for the air intake and vent
to be covered (on the carpet, cloth-
chair or table cloth, paper, plastic
bag which can easily be didodged,
or within 10cm of a wall, etc.)
• near the vent of a heater (See
illustration Q-Ial)
• on a warm electrical appliance
- smoky or steam
- ill ventilated (See illustration
Blbl)
If the air intake and vent ace
covered with a table cloth, etc. or
the unit is placed on the bedclothes,
it may present a risk of fire or
malfunction.
• extremely hot
If you leave the unit in a car whose
windows ace closed, especially in
sununer, its cabinet may warp or it
may cause a malfunction.
- under direct sunlight or near a
heating appliance
It may cause a malfunction to the
cabinet or parts.
- unstable
Be careful not to drop or let fall.
- vibrating
• easy {or insects to enter
• Avoid exposure to moislure, sand or
dust.
• Do not place near an AM radio or tuner.
• Do not operate where the temperature
is below 32»F (0*C) or above 14irF
(40"O.
• Do not point the lens toward the sun.
• Do not look into the lens while using.
• Note on the safety switch
The safety switch inside of the unit goes
into operation'.
- when the air intake or vent is covered
- when you use it in a stuffy place
• when the filler is dusty
When the safety switch functions,
disconnect the AC plug and leave the
unit for a couple of hours to be cool. If
the uiUt still does not work, contact
your nearest Sony dealer.
•This unit is only for NTSC color video
signals.
Specifications
Liquid crystal display: 13inches Total
dot nufflbenlTO thousand
Projecting lens: F1.75 f=2 l/s
inches(54.9mm)
Lens filler diameter I l/z inches
(37mm)
Bulb: 12V 5SW Halogen bulb
Speaker: 8 ohms
300mWx2 15/8 x l V t s inches
(40 X 30mm) diameter
Input jack:
S video input 4-pin mini DIN (1)
Luminance signal:! Vp-p,75 ohms,
unbalanced, sync negative
Chrominance signald)286Vp-p75
ohms, unbalanced
Video input Phono jack,lVp-p, 75
ohms, unbalanced, sync negative
Audio input Phono jack, -7SdBs
(0dBs.0.775Vnns)
Output jack: Headphone jack (Stereo
minijack)
Power requirements: 120 V AC, 60 Hz
Power consumption: SOW
Operating temperature: 32*F - t04°F
((PC-40^)
Storage temperature: -4"F - 140*F
(-20X:-40^C)
Dimensions:
Approx. 4 Vs X 6
2
X 6 > /4 inches
(w/h/d) (123 X162 X157 mm)
Mass: Approx. 3 lb 12 oz (1.7 kg)
Supplied accessories: Lenscap (1),
Halogen bulb (1), A/V connecting
cable (1), Filter sponge (1), Soft ease (1),
Operating Instructions (1)
Optional accessories:
Projection screen 5P)-N60
WideOmveision lens VCL-R0737
About the six* of the projected
plane (See illustration
D
J
Size of recommended projected plane is
up to 60 inches.
The distance in the illustrafion is
approximate.
Design and spedfications are subject to
change without notice.
Location of Controls
(Sea illustration
B )
|a1 POWERlamp Im| S VIDEO IN jack
|bl VOLUME •/-buttons Inl FtXUSring
(cl PHONES (headphones) jack lol Lens
(dl AC power cord (pi FILTER housing
(el POWER switch (ql PICTURE control
¡(1 Bulb-cover screw (tl Speaker
(g| Vent ls| Vent
(hi Bulb-cover (t) Air intake
(il Speaker lul Air intake (bottom)
(j| PROJECTION ANCLE switch |v| Tripod attachment (bottom)
(kl VIDEO IN jack (yellow)
(11 AUDIO IN jack (Left White/Right
Red)
Troubleshooting
If you run into any problems using the uniL use the following table to troubleshoot the
problem.
if the problem persists, consult your nearest Sony dealer.
Symptom
Check and adjust
The POWER lamp fladies red
•
Discormect the AC plug and remove any
and warning indicator appears
obstructions in the intake fan or vent fan.
on the picture.
•
Use the unit in nonrul temperature after it cools
"TEMP"
down.
"FAN"
•
Clean the filter.
•
Remove any obstructions that cover the air intake or
vent.
The power does not come on.
•
Tighten the screw of the bulb-cover completely.
•
Coimect the AC plug to a wall outlet.
The power is turned off during
Disconnect the AC plug and leave the unit for a
use.
couple of hours. Then use it after making sure that it
iscooL
The POWER lamp does not
•
Make sure of bulb installation.
light.
.
Replace the bulb with a new one.
No picture
•
Turn on the power of the video equipment
• Remove the lens cap.
•
Replace the bulb with a new one.
•
Make sure of bulb installation.
•
Make sure that the connecting cable is connected
correctly.
•
If the picture does not appear after more than five
minutes, the power is turned off to preserve the life
of the bulb.
This is not a malfunction.
To turn on the power again, set the POWER ssvitch
to OFF and then ON.
Constant bright points of light
This is a characteristic of the liquid crystal screen and
(ted, blue, or green) appear on
not 4 malfunction.
the screen.
No sound
•
Make sure that the connecting cable is connected
correctly.
•
Press VOLUME +.
Snow and distorted sound
•
Make sure that the cormecting cable is connected
correctly.
•
Move the unit away from an AM radio or tuiter.
Unclear picture
•
Adjust the focus by turning the FCXUS ring.
•
If the picture is still unclear after the focus is
adjusted, a function of the unit works to prevent the
line of liquid crystal display from appeating.on the
screen. This is not a malfunction.
Distorted picture
Adjust the angle of the lens or height using the tripod
so as to make the lens perpendicular to a ptt^ected
plane.
The picture is dark.
Adjust the brightness by turning the PICTURE
controL
A warm wind blows from vent. This is not a malfunction.
For Product information or operation, call:
SONYCUSTOMERINPORMATIONCENTER
201-368-9272
or write to:
Sony Customer Information Center
One Sony Drive
Park Ridge, New Jersey 07656-8003