beautypg.com

Dell Dimension 3000 User Manual

Page 35

background image

NOTE:

If you insert a boot device and restart the computer, this option appears in the system setup menu. To boot from a USB memory

device, select the USB device and move it so it becomes the first device in the list.

Drives

Diskette Drive

Identifies and defines the floppy drive attached to the FLOPPY connector on the system board as Off, USB, Internal, or Read Only.

Drives 0

through 3

Identifies the drives attached to the PRI IDE connectors on the system board, and lists the capacity for hard drives.

Onboard Devices

NIC Controller

You can set the NIC to On (default), Off, or On w/ PXE. When the On w/ PXE setting is active (available only for the future boot
process), the computer prompts the user to press . Pressing this key combination causes a menu to display that allows
you to select a method for booting from a network server. If a boot routine is not available from the network server, the computer
attempts to boot from the next device in the boot sequence list.

Audio

Controller

Enables or disables the onboard audio controller.

USB

Set to On (default) so that USB devices will be detected and supported in the operating system.

The No Boot option restricts external access to drive data. Use this option to prohibit users from booting the computer using an external
USB device.

Mouse Port

Enables or disables the onboard PS/2-compatible mouse controller.

LPT Port Mode

Identifies and defines the parallel port settings. You can set the parallel port to Off, AT, PS/2, EPP, or ECP.

LTP Port

Address

Identifies the address for the parallel port.

LPT Port DMA

Identifies and defines the parallel port DMA settings. You can set the parallel port DMA to Off, DMA1, or DMA3.

Serial Port #1

Identifies and defines the serial port settings. Auto, the default setting, automatically configures a connector to a particular designation
(COM1 or COM3).

Video

Primary Video

Specifies which video controller is primary when two video controllers are present on the computer.

Video Memory

Size

Sets the amount of system memory to be reserved for the onboard video controller.

Performance

Hyperthreading

If your computer's processor supports Hyper-Threading, these options appear in the Options List.

Performance

l

 

Bypass — Your computer does not test or change the current acoustics mode setting.

l

 

Quiet (default) — The hard drive operates at its most quiet setting.

l

 

Suggested — The hard drive operates at the level suggested by the drive manufacturer.

l

 

Performance — The hard drive operates at its maximum speed.

 

NOTE:

Switching to performance mode may cause the drive to be noisier, but its performance may not be affected.

 

NOTE:

Changing the acoustics setting does not alter your hard drive image.

Security

Displays available system security options.

Admin Password

Provides restricted access to the computer's system setup program in the same way that access to the system can be restricted with the
System Password option.

System Password

Displays the current status of the system's password security feature and allows a new system password to be assigned and verified.

Password Status

Locks the system password field with the setup password. When the field is locked, the option to disable password security by pressing
when the computer starts is no longer available.

Power Management

AC Recovery

Determines what happens when AC power is restored to the computer.

Auto Power On

Sets the computer to automatically turn on. Choices are every day or weekdays (every Monday through Friday).

The default setting is Off.

This feature does not work if you turn off your computer using a power strip or surge protector.

Auto Power Time

Sets time to automatically turn on the computer.

Time is kept in a 24-hour format (hours:minutes). Change the start-up time by pressing the right- or left-arrow key to increase or decrease
the numbers, or type numbers in both the date and time fields.

This feature does not work if you turn off your computer using a power strip or surge protector.

Low Power Mode

When Low Power Mode is selected, remote wakeup events no longer power up from Hibernate or Off.

Remote Wake Up

Allows the computer to power up when a NIC or Remote Wakeup-capable modem receives a wake up signal.

On is the default setting. On w/ Boot to NIC allows the computer to attempt to boot from a network prior to using the boot sequence.

 

NOTE:

Normally, the computer can be powered up remotely from suspend mode, hibernate mode, or when powered off. When Low

Power Mode (in the Power Management menu) is enabled, the computer can only be powered up remotely from Suspend.

Suspend Mode

The options are S1, a suspend state where the computer is running in a low-power mode, and S3, a standby state where the power is
reduced or turned off for most components, however, system memory remains active.