Dell PowerVault NX3600 - Manual (Page 2)

Setting Up Your Dell PowerVault Network Attached Storage Solution (continued)
Title Description
Getting Started Guide The Getting Started Guide provides an
overview of system features, setting up your
solution, and technical specifi cations.
This document is shipped with your system
and is also available at support.dell.com/
manuals.
Deployment Guide The Deployment Guide provides information
about the deployment of the hardware and
software for the solution. This document is
available at support.dell.com/manuals.
Owner’s Manual The Owner’s Manual provides information
about solution features and describes how
to troubleshoot the system and install or
replace system components. This document
is available at support.dell.com/manuals.
Rack Installation Instructions The rack documentation included with your
rack solution describes how to install your
system into a rack. This document is shipped
with your rack solution and is also available
at support.dell.com/manuals.
Administrator’s Guide The Administrator’s Guide provides
information about confi guring, managing,
and troubleshooting the software and the
solution. This document is available at
support.dell.com/manuals.
Online Help The Online Help provides information about
confi guring and managing the software.
The online help is integrated with the system
and can be accessed from the NAS Manager
web interface.
Information in this publication is subject to change without notice.
© 2012 Dell Inc. All rights reserved.
Reproduction of these materials in any manner whatsoever without the written
permission of Dell Inc. is strictly prohibited.
Dell™, the DELL logo, and PowerVault™ are trademarks of Dell Inc.
Other trademarks and trade names may be used in this publication to refer to either
the entities claiming the marks and names or their products. Dell Inc. disclaims any
proprietary interest in trademarks and trade names other than its own.
Printed in the U.S.A.
2012 - 04
4
|
Preparing Your Environment for Setting Up the PowerVault NX3600/NX3610 Solution
The setup worksheet helps you plan your confi guration.
Recording the IP addresses of your solution in a single location enables you to confi gure your setup faster and more effi ciently.
Terms Used In the IP Chart
Controller—A server appliance installed with the Dell scalable fi le system software.
An essential component of a PowerVault NAS clustered solution.
Interconnect Private Network—A Class C subnet that is not used in your
environment.
SAN network/iSCSI network—The network that carries the block level (iSCSI) traffi c
and to which the storage subsystem is connected. It is recommended that this
network be separated from the client network.
NAS cluster name—The name that is used to identify the PowerVault NX3600/NX3610
solution.
NAS management VIP—IP address that the management stations use to access the
PowerVault NX3600/NX3610 controllers.
Client access VIP—IP address that clients use to access CIFS shares and NFS exports
hosted by a PowerVault NAS solution. The PowerVault NAS solution supports multiple
client access VIPs.
MD discovery IP—The MD discovery IP is an MD storage array (iSCSI) IP address from
either the SAN A or SAN B network.
5
|
Deploying Your NAS Solution
PowerVault FluidFS NAS Setup Worksheet
Number of
NAS Appliances 1 Number of
MD Series Arrays 1 Type of
Network Routed
2* 2* Flat
NAS Cluster
Name: Subnet Mask: Gateway:
Primary Client Network iSCSI SAN Network
Management VIP: SAN A SAN B
NAS Appliance 0 Controller 0
Controller 0 IP Controller 1
Controller 1 IP
NAS Appliance 1*
*Controller 2 IP *Controller 2
*Controller 3 IP *Controller 3
Client VIPs MD Series iSCSI Address
Flat Network needs only one VIP Array #1 Management
Routed Networks need four VIPs per appliance Controller 0-0 SAN A
1 appliance = 4; * 2 appliances = 8 Controller 0-1 SAN B
Controller 1-0 SAN A
Client VIP # 1 Controller 1-1 SAN B
Client VIP # 2
Client VIP # 3 *Array #2 Management
Client VIP # 4 Controller 0-0 SAN A
*Client VIP # 5 Controller 0-1 SAN B
*Client VIP # 6 Controller 1-0 SAN A
*Client VIP # 7 Controller 1-1 SAN B
*Client VIP # 8 Use one IP for iSCSI Discovery in a NAS IDU.
Environment Setup
DNS Server IP SNMP Read
Community NIS Domain
DNS Suffi x SNMP Trap
Recipient NIS Server
NTP Server IP NetBIOS Name LDAP Server
SMTP Server IP Active Directory
Domain LDAP Distin-
guished
Name
SMTP From
E-mail Address
Switch Requirements Checklist
Client Network SAN/Internal Network
Jumbo Frames Enabled
9216 MTU Recommended Required
Port Fast Enabled Required Required
Flow Control Enabled Recommended Required
Interconnect Private Network
Select a private Class C subnet
10.255.254.x
172.31.254.x
192.168.254.x
___.___.___.x
*Applicable only to NX3610.
Launching the Initial Deployment Utility
NOTE: Download and install the NAS IDU from support.
dell.com.
The NAS IDU guides you through the network confi guration
and enables you to set up and
access the PowerVault NX3600/NX3610 solution from the
management station.
NOTE: The following steps must be performed by trained
personnel. For more information on deploying your NAS
solution, see the Dell FluidFS NX3600/3610 NAS Solutions
Deployment Guide at support.dell.com/manuals.
From the management station, launch the 1. NAS IDU
and follow the instructions on the screen.
After the confi guration is complete, the Confi gurations
Results screen is displayed.
Completing the Setup
Copy the IQN numbers from the 2. Confi guration
Results screen.
NOTE: Do not close the Confi guration Results screen.
Launch the 3. Modular Disk Storage Manager (MDSM)
client.
Create a disk group pair.
4.
NOTE: It is recommended that you create a disk group
for each virtual disk. However, you can create multiple
virtual disks in a disk group.
Create virtual disk pairs.
5.
These virtual disks must be created in pairs and must
be of the same size.
Create hosts and host groups. 6.
Map the virtual disks to the host group. 7.
Repeat step 4 through step 6 for controller 1. 8.
Close the MDSM 9. client.
In the 10. Confi guration Results screen in the NAS IDU,
click Finish.
The NAS Manager web interface is launched and the
PowerVault Confi guration Wizard is displayed.
NOTE: If the web interface does not automatically
launch, select Cluster Management → Maintenance→
Start Confi guration Wizard.
6
|
Confi guring Your NAS Solution 7
|
Documentation
The PowerVault NAS Manager web interface provides
information about the controllers and guides you
through the steps necessary to confi gure the network
for your clustered NAS solution.
NOTE: If the Start Confi guration Wizard does not open
automatically, locate it under Cluster Management →
Maintenance → Start Confi guration Wizard.
NOTE: If your web browser does not display the
PowerVault NAS Manager web interface, check the security
settings of the web browser, accept the security
certifi cate, and ensure that JavaScript is enabled.
To access the PowerVault NAS Manager web interface at
a later time, type the following URL in your web browser:
https://
The NAS Management VIP is the VIP of the
management station.
Default User Name and Password
The default user name for the solution is admin
The default password for the solution is Stor@ge!
To complete the system confi guration, complete the
following steps using the Start Confi guration Wizard:
Configuring DNS •
Configuring time •
Configuring E-mail •
Configuring SNMP •
Setting up file system •
Changing the administrator password •
Configuring system identity •
Configuring identity management •
Configuring cross protocol •
Creating NAS volumes •
Creating CIFS shares •
Creating NFS exports •
After completing the Start Confi guration Wizard,
confi gure additional Client VIPs in the NAS Manager web
interface at Cluster Management → Network→
Subnets → Primary.