System codes and messages, Diagnostic codes – Dell Dimension 8200 User Manual
Page 2
Back to Contents Page
System Codes and Messages
Dell™ Dimension™ 8200
Diagnostic Codes
Your computer is equipped with four diagnostic lights, which are labeled "A," "B," "C," and "D" on the back of the computer. Each of the four lights can be
yellow, green, or off as shown in the following table. When the computer is turned on or restarted and it is functioning normally, the lights flash during POST.
After the computer starts, the lights remain green to signify normal computer operation.
If a malfunction is detected and the computer fails to start, the lights display a code that identifies the problem. Write down the diagnostic code displayed and
look it up in the following table.
Diagnostic Code
Definition
Corrective Action
Power up default.
Make sure that the computer is connected to a known working electrical outlet, and then check
whether the front-panel power light on the
power button
is on or off. If the power light is off, check
the
power supply
. If the problem persists, see "Contacting Dell" in the Solutions Guide for instructions
on obtaining technical assistance.
See "
Safety Instructions
," and then
remove all cards
. If the computer still does not start, see
"Contacting Dell" in the Solutions Guide for instructions on obtaining technical assistance.
System board is receiving
power, but the BIOS is not
executing.
Set the
configuration jumper
to Maintenance mode, and restart the computer. Exit and save changes
in the
system setup program
. Turn off the computer and reset the configuration jumper to Normal
mode, and then restart the computer.
See "
Safety Instructions
," and then
remove all cards
and restart the computer to determine if a
resource conflict exists. If conflict exists, see"
Resolving Software and Hardware Incompatibilities
." If
the problem persists, see "Contacting Dell" in the Solutions Guide for instructions on obtaining
technical assistance.
Recovery mode from BIOS
failure.
Set the
configuration jumper
to Maintenance mode and restart the computer. Exit and save changes in
the
system setup program
. Turn off the computer and reset the configuration jumper to Normal mode,
and then restart the computer.
See "
Safety Instructions
," and then
remove all cards
and restart the computer to determine if a
resource conflict exists. If conflict exists, see "
Resolving Software and Hardware Incompatibilities
." If
the problem persists, see "Contacting Dell" in the Solutions Guide for instructions on obtaining
technical assistance.
Microprocessor has failed a
BIOS test.
If the problem persists, see "Contacting Dell" in the Solutions Guide for instructions on obtaining
technical assistance.
Memory failed to be sized or
enabled.
Reseat the memory modules
. If the problem persists, see "Contacting Dell" in the
Solutions Guide for
instructions on obtaining technical assistance.
Memory modules are
detected, but a memory
configuration or compatibility
error exists.
l
Be sure that there are no special memory module/memory connector placement
requirements
.
l
Verify that the memory modules that you are installing are
compatible with the computer
.
If the problem persists, see "Contacting Dell" in the Dell Owner's Manual for instructions on obtaining
technical assistance.
No memory modules are
detected.
l
Reseat all memory modules
, and then restart the computer.
l
To eliminate the possibility of a faulty memory connector,
remove all memory modules
,
reinstall
one memory module
(if the computer supports a single module), and then restart the computer.
If the computer starts normally, move the memory module to a different connector and restart
the computer. Continue until you have identified a faulty connector or reinstalled all modules
without error.
If the problem persists, see "Contacting Dell" in the Dell Owner's Manual for instructions on obtaining
technical assistance.
PCI bus failure has occurred.
See "
Safety Instructions
," and then
remove all cards
and restart the computer to determine if a
resource conflict exists. If conflict exists, see "
Resolving Software and Hardware Incompatibilities
." If
the problem still persists, see "Contacting Dell" in the Solutions Guide for instructions on obtaining
technical assistance.
Video controller failed to
initialize or respond.
If the computer has a video card,
reseat the video card
. If the problem persists or the computer has
integrated video, see "Contacting Dell" in the Solutions Guide for instructions on obtaining technical