Dell SP2009WFP Monitor - Manual (Page 31)

4. Carefully inspect the screen for abnormalities.
5. Press the forth button on the front panel again. The color of the screen changes to red.
6. Inspect the display for any abnormalities.
7. Repeat steps 5 and 6 to inspect the display in green, blue, and white colored screens.
The test is complete when the white screen appears. To exit, press the forth button again.
If you do not detect any screen abnormalities upon using the built-in diagnostic tool, the monitor is functioning properly. Check the video card and computer.
Common Problems
The following table contains general information about common monitor problems you might encounter and the possible solutions.
Common Symptoms What You Experience Possible Solutions
No Video/Power LED off No picture l Ensure that the video cable connecting the monitor and the computer is properly connected and
secure.
l Verify that the power outlet is functioning properly using any other electrical equipment.
No Video/Power LED on No picture or no brightness l Increase brightness & contrast controls via OSD.
l Perform monitor self-test feature check.
l Check for bent or broken pins in the video cable connector.
l Run the built-in diagnostics.
Poor Focus Picture is fuzzy, blurry, or
ghosting l Perform Auto Adjust via OSD.
l Adjust the Phase and Pixel Clock controls via OSD.
l Eliminate video extension cables.
l Reset the monitor to Factory Settings.
l Change the video resolution to the correct aspect ration (16:10).
Shaky/Jittery Video Wavy picture or fine
movement l Perform Auto Adjust via OSD.
l Adjust the Phase and Pixel Clock controls via OSD.
l Reset the monitor to Factory Settings.
l Check environmental factors.
l Relocate the monitor and test in another room.
Missing Pixels LCD screen has spots l Cycle power on-off.
l Pixel that is permanently off is a natural defect that can occur in LCD technology.
l Run the built-in diagnostics
Stuck-on Pixels LCD screen has bright
spots l Cycle power on-off.
l Pixel that is permanently off is a natural defect that can occur in LCD technology.
l Run the built-in diagnostics
Brightness Problems Picture too dim or too
bright l Reset the monitor to Factory Settings .
l Auto Adjust via OSD.
l Adjust brightness & contrast controls via OSD.
Geometric Distortion Screen not centered
correctly l Reset the monitor to Factory Settings.
l Auto Adjust via OSD.
l Adjust brightness & contrast controls via OSD.
NOTE: When using 'DVI-D', the positioning adjustments are not available.
Horizontal/Vertical Lines Screen has one or more
lines l Reset the monitor to Factory Settings.
l Perform Auto Adjust via OSD.
l Adjust Phase and Pixel Clock controls via OSD.
l Perform monitor self-test feature check and determine if these lines are also in self-test mode.
l Check for bent or broken pins in the video cable connector.
l Run the built-in diagnostics
NOTE: When using 'DVI-D', the Pixel Clock and Phase adjustments are not available.
Synchronization Problems Screen is scrambled or
appears torn l Reset the monitor to Factory Settings.
l Perform Auto Adjust via OSD.
l Adjust Phase and Pixel Clock controls via OSD.
l Perform monitor self-test feature check to determine if the scrambled screen appears in self-
test mode.
l Check for bent or broken pins in the video cable connector.
l Restart the computer in the safe mode.
Safety Related Issues Visible signs of smoke or
sparks l Do not perform any troubleshooting steps.
l Contact Dell immediately.
Intermittent Problems Monitor malfunctions on &
off l Ensure that the video cable connecting the monitor to the computer is connected properly and
is secure.
l Reset the monitor to Factory Settings.
l Perform monitor self-test feature check to determine if the intermittent problem occurs in self-
test mode.
Missing Color Picture missing color l Perform monitor self-test feature check.
l Ensure that the video cable connecting the monitor to the computer is connected properly and
is secure.
l Check for bent or broken pins in the video cable connector.
l Run the built-in diagnostics
Wrong Color Picture color not good l Change the Color Setting Mode in the Color Settings OSD to Graphics or Video depending on
the application.
l Try different Color Preset Settings in Color Settings OSD. Adjust R/G/B value in Color Settings
OSD if the Color Management is turned off.