Vermont Casting 1610CE User Manual
Page 15
15
Defiant 1610CE Non-Catalytic Woodburning Stove
30003846
Defiant
ST521
Intrepid
loading
11/00
ST521
Fig. 28 Top loading is the best way to add fuel during regular
use. Front loading is useful for kindling a fire.
In addition, however, the front doors open as well for
adding an occasional log to a fire. The Defiant NC is
not approved for operation in Europe with the front
doors open.
To open the front doors, insert the handle into the door
latch stub and turn it to the left and up. (Fig. 29)
To close them, always close the left door first. Turn the
handle in the right door to the left and up (to the open
position) and close it. Finally, push on the door as you
turn the handle to the right and down. The doors will
draw in slightly, and the handle should offer some resis-
tance as you turn it to the closed position.
To reduce the risk of breaking the glass, avoid striking
the glass or slamming the doors.
When you are not using the door handle, store it in the
holder behind the right front leg of the stove. Be careful
to not drop the handle, since it is breakable.
ST544
door open
11/00
Clockwise to
Open
Counter-
clockwise
to Close
ST544
Fig. 29 To open the front doors, turn the handle clockwise.
This stove is designed to operate efficiently with
the fire doors (front doors and griddle) closed. The
firebox and ash doors should be kept closed at all
times except when refueling or removing ashes.
Infra-Red Reflective Glass Panels
for Clear Fire Viewing
The outer surfaces of the ceramic glass panels have
an infrared-reflective coating which keeps the inner
surfaces warm. This design, along with a pre-heated
‘airwash,’ makes clear fire viewing possible at most fir-
ing levels.
Andirons Help Protect the Glass
Your stove has andirons to keep logs away from the
glass panels. The andirons are essential to maintain
clear fire viewing, and should be left permanently in
place. Since the andirons may slightly hinder refueling
through the front doors, most stove owners will prefer
the convenience of top loading through the griddle. Do
not place fuel between the andirons and the doors.
Burn Only High-Quality Wood
The Defiant is designed to burn natural wood only; do
not burn fuels other than that for which it was designed.
You’ll enjoy the best results when burning wood that
has been adequately air-dried. The wood should be
559-610 mm (22-24”) in length. Avoid burning “green”
wood that has not been properly seasoned. Do not
burn construction materials; they often contain
chemicals and metals that can damage the inside
surfaces of the stove and pollute the air. Do not burn
ocean driftwood; when it burns, the salt it contains will
attack the cast iron.
The best hardwood fuels include oak, maple, beech,
ash, and hickory that has been split, stacked, and air-
dried outside under cover for at least one year.
If hardwood is not available, you can burn softwoods
that include tamarack, yellow pine, white pine, East-
ern red cedar, fir, and redwood. These should also be
properly dried.
Store wood under cover to keep it dry. The longer it is
stored, the better heating and fire-viewing performance
you will enjoy. Even for short-term storage, be sure to
keep wood a safe distance from the heater and keep
it out of the areas around the heater used for refueling
and ash removal.
A Surface Thermometer is a Valuable
Guide to Operation
An optional surface thermometer tells you when to ad-
just the air control, and when to refuel. (Fig. 30)
ST523
Intrepid
temp readings
11/00
ST523
Fig. 30 Take temperature readings with a thermometer lo-
cated in the middle of the griddle.
For example, when the thermometer registers at least
230° C (450° F) after start-up you know the stove is
hot enough and it may be time to close the damper.
Note that the stove will warm up much sooner than the
chimney, though; a warm chimney is the key to easy, ef-
fective stove operation. Please review the draft man-