Quoizel TFF16191A5VA Inglenook User Manual
Warnings and cautions, Care of tiffany style shade

Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Bulb Recommended:
Estimated Assembly Time:
Preparation:
(2) Medium Base 75W Maximum, Alternate bulb (2) 19W CFL
20-30 minutes
Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
Warnings and Cautions
1of1
Assembly Instruction Sheet #IS-TFF16191A5VA
For Style TFF16191A5VA
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,
.
.
.
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2014 QuoizelInc.
February2014
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Care of Tiffany Style Shade
A new tiffany lamp shade has an oil film applied to the shade that protects the tiffany shade from scratches during shipment. If the oil applied is
too heavy you can remove the excess oil film with a paper towel. Gently wipe away the excess oil.
For general cleaning of tiffany shades use a gentle lemon oil-based furniture polish applied to a soft cloth and wipe gently.
If a white powder appears on the soldered joints of the tiffany shade this is a normal oxidation process. Use a small amount of lemon oil or
mineral oil applied directly to oxidized areas and the soldered area will return to like new.
STEP 1
Install Rods
Socket Assembly
and Shade
-
,
A. Thread the Socket
Assembly, the
, the
and the
Base together as shown.
Hand tighten until snug.
B. Pull the cord from the Base
as you assemble the parts
together to remove the
excess cord between parts.
C. Thread have hex nut end of
Nipple with Hex Nut into the
hex coupling, hand tighten
until sung.
D. Place Spacer and Check
Ring over the Nipple with
Hex Nut, secure by
threading the Small Knurled
Nut onto the nipple. Hand
tighten until sung.
E. Thread the Big Knurled Nut
onto the Nipple, hand
tighten until snug.
F. Place the Flat Washer and
the Shade over the Nipple.
Secure by threading the
Finial onto the Nipple. Hand
tighten until snug.
G.This fixture uses standard
bulb with medium base .
Maximum 75 watts. Insert
bulb and screw snugly into
place.
Your fixture is now
assembled and ready to
use. Enjoy!
Rod
Threaded Rods
Figure 1
TFF16191A5VA
PART NUMBER
NOTE: ALL DIMENSIONS ARE ROUNDED
UP TO THE NEAREST 1/2
"
REPLACEMENT PART DESCRIPTION
NO.
(2) 75W
Bulbs
(Not Supplied)
Medium
Base
1
2
3
1885UVBTF BASE VALIANT BRONZE TFF16191A5VA
FINIAL
1.04H X .98 Q
VALIANT BRONZE
S
GLASS TIFFANY 8H X 17SQ.
REQ.
1
1
1
2
11”SQ.
62”
9”
17” SQ.
M1373FIVA
G1858SH
Base
x 1
Threaded
Rod
x 1
Rod
x 1
Socket
Assembly
x 1
Shade x 1
Bulb (not
included)
Finial
X 1
Big Knurled Nut x 1
Check Ring
x 1
Small Knurled Nut
x 1
Nipple with
Hex Nut
x 1
Spacer
x 1
Flat Washer x 1
1
3