Quoizel TF489T Tiffany - Manual

Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Bulb Recommended:
Estimated Assembly Time:
Preparation:
(2) Medium Base 60W Maximum, Alternate bulb (2) 13W CFL
20-30 minutes
Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
Warnings and Cautions
1of1
Assembly Instruction Sheet #IS-TF489T
For Style TF489T
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
, .
. .
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2014 QuoizelInc. April2014
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Care of Tiffany Style Shade
A new tiffany lamp shade has an oil film applied to the shade that protects the tiffany shade from scratches during shipment. If the oil applied is
too heavy you can remove the excess oil film with a paper towel. Gently wipe away the excess oil.
For general cleaning of tiffany shades use a gentle lemon oil-based furniture polish applied to a soft cloth and wipe gently.
If a white powder appears on the soldered joints of the tiffany shade this is a normal oxidation process. Use a small amount of lemon oil or
mineral oil applied directly to oxidized areas and the soldered area will return to like new.
STEP 1 Install Nipple with
HEX Nut, Shade and
Bulb
-
A. Thread have hex nut end of
Nipple with Hex Nut into Hex
Coupling on the top of Base .
B. Place Spacer and Check
Ring over the Nipple. Secure
by thread Small Knurled Nut
onto the Nipple, hand tighten
until snug.
C. Thread Big Knurled Nut onto
Nipple. Hand tighten until
snug.
D. Place the Flat Washer and
the Shade over the Nipple.
Adjust the Big Knurled Nut to
proper location for the Flat
Washer, the Shade and
Finial. secure by thread
Finial onto the Nipple, hand
tighten until snug.
E. This fixture uses standard
bulb with medium base .
Maximum 75 watts. Insert
bulb and screw snugly into
place.
Your fixture is now
assembled and ready to
use. Enjoy!
Finial
X 1
Shade
X 1
Figure 1
Bulb (not
included)
TF489T
PART NUMBER
NOTE: ALL DIMENSIONS ARE ROUNDED
UP TO THE NEAREST 1/2 "
REPLACEMENT PART DESCRIPTION NO.
(2) 60W
Bulbs
(Not Supplied)
Medium
Base
1
2
1489TTF
J976FI
BASE TF489T
FINIAL 1.25H X 1D
REQ.
1
1
1
Flat
Washer
x 1
Big Knurled
Nut x 1
Check Ring
Spacer
x 1
Small Knurled
1 x Nut
Base
x 1
Nipple with
Hex Nut x 1
15.5” Dia.
6.5”
6.5”
22.5”
3 G8324SH SHADE TIF 7H X 15.5D 1
2
3
FINISH: VINTAGE BRONZE