Quoizel MC120T Mica - Manual

1of1
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2014 QuoizelInc. March2014
A. Thread the Socket Assembly onto
the Base, hand tighten until sung.
B. Thread have hex nut end of
Nipple with Hex Nut into the hex
coupling, hand tighten until sung.
C. Place Spacer and Check Ring
over the Nipple with Hex Nut,
secure by threading the Small
Knurled Nut onto the nipple.
Hand tighten until sung.
D. Thread the Big Knurled Nut onto
the Nipple, hand tighten until
snug.
E. Place the Shade A over the
Nipple. Secure by threading the
Finial onto the Nipple. Hand
tighten until snug.
G. This fixture uses standard bulb
with medium base . Maximum 60
watts.
H. Insert bulb and screw snugly into
place.
Your fixture is now assembled
and ready to use. Enjoy!
F. Place the Shade B over the
Shade A.
Hex
Coupling
Bulb
Base
MC120T
FINISH:
16.5” Dia.
9”
25”
PART NUMBER
1120TMC
M1469FIT
S367MC
NOTE: ALL DIMENSIONS ARE ROUNDED UP
TO THE NEAREST 1/2
"
REPLACEMENT PART DESCRIPTION
BASE MICA TABLE LAMP
FINIAL 2.5H X 1.75D MC120T
SHADE SOFT GREEN MICA RPL MC120T
NO.
(2) 75W
Bulbs
(Not Supplied)
Medium
Base
1
2
3
REQ.
1
1
1
3
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Bulb Recommended:
Estimated Assembly Time:
Preparation:
(2) Medium Base 60W Maximum, Alternate bulb (2) 13W CFL
20-30 minutes
Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
Warnings and Cautions
Assembly Instruction Sheet #IS-MC120T
For Style MC120T
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
, .
. .
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Care of Tiffany Style Shade
A new tiffany lamp shade has an oil film applied to the shade that protects the tiffany shade from scratches during shipment. If the oil applied is
too heavy you can remove the excess oil film with a paper towel. Gently wipe away the excess oil.
For general cleaning of tiffany shades use a gentle lemon oil-based furniture polish applied to a soft cloth and wipe gently.
If a white powder appears on the soldered joints of the tiffany shade this is a normal oxidation process. Use a small amount of lemon oil or
mineral oil applied directly to oxidized areas and the soldered area will return to like new.
Socket
Assembly
Spacer
Nipple with
Hex Nut
Check Ring
Small
Knurled Nut
Big Knurled
Nut
Shade B
Finial
Shade A
8.5” Dia.
1
2