Quoizel TF6668VB Gotham - Manual

Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Bulb Recommended:
Estimated Assembly Time:
Preparation:
(2) Medium Base 75W Maximum, Alternate bulb (2) 19W CFL
20-30 minutes
Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
Warnings and Cautions
1of1
Assembly Instruction Sheet #IS-TF6668VB
For Style TF6668VB
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
, .
. .
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2014 QuoizelInc. June2014
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Care of Tiffany Style Shade
A new tiffany lamp shade has an oil film applied to the shade that protects the tiffany shade from scratches during shipment. If the oil applied is
too heavy you can remove the excess oil film with a paper towel. Gently wipe away the excess oil.
For general cleaning of tiffany shades use a gentle lemon oil-based furniture polish applied to a soft cloth and wipe gently.
If a white powder appears on the soldered joints of the tiffany shade this is a normal oxidation process. Use a small amount of lemon oil or
mineral oil applied directly to oxidized areas and the soldered area will return to like new.
Assembly Instructions:
A. Thread the Socket Assembly
and the Base together as
shown. Hand tighten until
snug.
B. Thread have hex nut end of
Nipple into the hex coupling,
hand tighten until sung.
C. Place Spacer and Check
Ring over the Nipple, secure
with the Small Knurled Nut
and hand tighten until sung.
D. Thread the Big Knurled Nut
onto the Nipple, adjust it to
proper location for rest
components. Place the flat
washer and the Shade over
the Nipple. Secure them with
the Finial. Hand tighten until
snug.
F.This fixture uses standard
bulb with medium base .
Maximum 75 watts. Insert
bulb and screw snugly into
place.
Your fixture is now
assembled and ready to
use. Enjoy!
Finial
X 1
Shade
X 1
Base
X 1
Figure 1
Bulb (not
included)
TF6668VB
PART NUMBER
NOTE: ALL DIMENSIONS ARE ROUNDED
UP TO THE NEAREST 1/2"
REPLACEMENT PART DESCRIPTION NO.
(2) 75W
Bulbs
(Not Supplied)
Medium
Base
1
2
3
4
16 668VBT
M014FIR
BASE VINTAGE BRONZE TABLE LAMP
FINIAL ARC BRONZE
GLASS TIFFANY 5.75H X 19.25D
BALL 5/8" DIA BRASS
REQ.
1
1
1
2
2
7 ”SQ.
24.5 ”
5.5 ”
19 ” Dia.
1
Big Knurled
Nut x 1
Check Ring
x 1 Small Knurled
Nut x 1
Nipple with
Hex Nut x 1
Spacer
x 1
3
Socket Assembly
x 1
G6906SH
M860BLA
4
Flat Washer
x 1