Quoizel UPWS1722BN Uptown Wall Street User Manual
Package contents, Warnings and cautions

Package Contents
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Bulb Recommended:
Estimated Assembly Time:
Preparation:
(2) Medium Base Maximum 100W, Alternate bulb (2) 23W CFL Maximum.
30-45 minutes
Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-UPWS1722BN
For Style UPWS1722BN
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at
2014 QuoizelInc.
May2014
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
E
B
Shade
x 1
Lock Screw
x 4
Crossbar Assembly
x 1
STEP 1
Install Ring to Socket Assembly
-
A. Adjust Side Arms on Socket Assembly (C)
to a straight line. Attach side arms to Ring
(D) and secure with Lock Screws (E).
Hand tighten until snug with screwdrivers.
C
A
D
Ring
x 1
Figure 1
Unfold Side Arms
Supply Wires with
Ground Wire
Outlet Box Screws
(not included)
Outlet
Box
Figure 2
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
F
STEP 2
Install Crossbar Assembly
-
A. Pass supply wires through Crossbar Assembly (A). Attach Crossbar
Assembly (A) to Outlet Box with the head of Green Ground Screw
facing you. Secure it with Outlet Box Screws (not included). Tighten
until snug.
A
D
White wire
from supply
Ribbed side wire
from fixture
Black wire from
supply (or Red)
Smooth side wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 3
C
Socket Assembly
x 1
Hex Nut
x 1
G
H
Flat Washer
x 1
I
Rubber Washer
x 1
Finial
x 1
E
STEP 4 - Install Fixture Body
A. Carefully tuck all wires into the outlet box and position ceiling
canopy on Socket Assembly (C) over the outlet box. Align the holes
in ceiling canopy with the mounting screws, then attach ceiling
canopy using the previously removed mounting balls. Hand tighten
until snug.
A
Mounting Screw
Mounting Ball
C
Figure 4
STEP 5 - Attach Finial to Shade
A. Attach Finial (I) to the bottom of Shade (B), pass through the center
hole of Shade (B). Place Rubber Washer (H) and Flat Washer (G)
B
G
H
over the nipple of Finial (I)
and secure with Hex Nut
(F). Tighten until snug
gently.
Figure 5
F
I