Quoizel PCBV1613C Platinum Collection Bravado User Manual

Package contents, Warnings and cautions, Hardware contents

Package Contents

Quoizel, Inc.
6 Corporate Parkway
Goose Creek, SC 29445

Customer Service
Phone 631.273.2700
Fax

631.231.7102

www.quoizel.com

Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape,
safety glasses.
Bulb Recommended:
Estimated Assembly Time:
Preparation:

(2) Medium Base 60W bulbs Maximum, Alternate bulb (2) 13W CFL Maximum.

20-30 minutes

Identify and inspect all parts before beginning installation. Check package content list and diagrams

below to be sure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or
operate the fixture. Contact customer service for replacement parts.

Warnings and Cautions

1of2

Assembly Instruction Sheet #IS-PCBV1613C

For Style PCBV1613C

Thank you for purchasing a Quoizel product.

Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700

or visit us on-line at www.quoizel.com

2014 QuoizelInc.

January2014

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.

Bushing
x 3

Ring
x 1

Knurled Nut
x 3

Shade
x 1

Lock Screw
x 3

x 3

Rubber Washer

Lock Ring
x 3

Hardware Contents

Crossbar
x 1

Mounting Ball
x 1

STEP 1

Install Crossbar

A. Attach the Lock Screw (C) from the top of the Ceiling Canopy (A).

Place the

(D), the Bushing (E), the Ring (B) and the

(F) over the end of the Lock Screws (C) in turn.

Secure them together with the Lock Ring (G). Tighten until snug

Knurled Nut

Rubber Washer

Figure 1

Ceiling
Canopy
x 1

STEP 3

Install Nipple to Crossbar

* Pliers is required for this step.

A. Thread one Hex Nut (CC) to the middle of the Nipple (DD). Place the

Lock Washer (BB) over the Nipple (DD) and then thread the Nipple
(DD) into the Crossbar (AA) until the Nipple (DD) is about 0.375”
above the Crossbar (AA).

B. Position the center hole of the Ceiling Canopy (A) over the end of

the Nipple (DD). Adjust the Nipple (DD) so approx 0.375” of the
Nipple (DD) is protruding from the mounting hole on the Ceiling
Canopy (A). This adjustment may take a few tries.

C. Remove the Ceiling Canopy (A) and then tighten the Hex Nut (CC)

against the Crossbar (AA) to secure in place.

D. Thread another Hex Nut (CC) onto the end of the Nipple (DD).

Thread this Hex Nut (CC) on just enough so the inside surface of the
Ceiling Canopy (A) rests against it. * You may have to trial fit the
Ceiling Canopy (A) one more times to insure this distance also. This

Finial
x 3

Lock Washer
x 1

Hex Nut
x 2

Nipple
x 1

Step A

Step D

STEP 2

Install Crossbar

AA)

Attach the Crossbar (

to the Outlet Box with the head of the

Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included) Tighten until snug

Figure 2

Outlet Box

Outlet Box Screw
(not included)

Green Ground Screw

Figure 3