Quoizel TF1816VB Tiffany - Manual (Page 2)

2of2
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2014 QuoizelInc.
STEP 3 - Install Fixture Chain and Ceiling Canopy
A. Adjust the Fixture Chain (GG) to your desired length by removing
the links if needed.
Pliers is required for this step.
B. With the Fixture Chain (GG) not attached to the Fixture Loop and the
Canopy Chain Loop (EE), pull the supply wires through the Fixture
Chain (GG) alternating links. After the wires are through the Fixture
Chain (GG), pull the Supply Wires and the Ground Wire through the
Canopy Lock Ring (FF) and the Ceiling Canopy (HH) in order.
C. Attach one end of the Fixture Chain (GG) to the Fixture Loop . Lift
the fixture and Fixture Chain (GG) up And Attach the other end of the
Fixture Chain (GG) onto the Canopy Chain Loop (EE) . The fixture
will now hang safely. Close the chain loop at the Ceiling Canopy
Loop (EE).
D. Feed the Supply Wires and Ground Wire through the Canopy Chain
Loop (EE) and Nipple (DD) into the Outlet Box. Cut the wires leaving
approximately 8” of wire extending from the Outlet Box.
E. Refer to Step 5 for wire connections.
F. Raise the Ceiling Canopy (HH) and Canopy Lock Ring (FF) up the
Fixture Chain (GG) and over the Canopy Chain Loop (EE). Tighten
the Canopy Lock Ring (FF) onto the Canopy Chain Loop (EE) until
tight.
Suggested chain length for Ceiling height :
8’ ceiling : use 4 links of chain and 2 quick links
9’ ceiling : use 14links of chain and 2 quick links
10’ ceiling : use 24 links of chain and 2 quick links
*
Figure 3
DD
GG
Supply Wires
and Ground Wire
EE
FF
HH
STEP 5 - Install Shade and
Bulb
A. Thread have hex nut end of
Nipple with Hex Nut (C) onto
the hex coupling on the
bottom of Socket Assembly
(A). Hand tighten until sung.
B. Place the Shade (D) over the
nipple, secure by threading
Finial (E) onto the nipple.
Hand tighten until sung.
C. Place the Loop on the Side
Chain (B) onto the Hook on
the side of Socket Assembly
(A), the Hook on the Side
Chain (B) onto the Loop
inside of Shade (D).
D. This fixture uses standard
bulb with medium screw
base. Maximum 100 watts.
E. Insert bulb and screw snugly
into place.
Your fixture is now
assembled and ready to use.
Enjoy!
June2014
Fixture Loop
TF1816VB
PART NUMBER
NOTE: ALL DIMENSIONS ARE ROUNDED
UP TO THE NEAREST 1/2
"
REPLACEMENT PART DESCRIPTION REQ.
NOTE: TWO LIGHTS SHOWN FOR
ILLUSTRATION PURPOSES ONLY.
FINISH: VINTAGE BRONZE
NO.
1
STEP 4 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
White wire
from supply
Ribbed side wire
from fixture
Black wire from
supply (or Red) Smooth side wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 4
(4) 100W
Bulbs
(Not Supplied)
Medium
Base
Figure 5
Socket
Bulb
Hook
A
B
C
D
E
Loop
Hook
Loop
5.5” Dia.
2”
76.5”OVERALL HEIGHT
INCLUDES 48” CHAIN ( )
25”
7”
22.5” Dia.
2
3
4
11816VBT
M052CHVB
C108FIR
G6019SH
BASE
CHAIN
FINIAL
SHADE
1
1
1
1
1
2
4
3