Quoizel GE5006SE Genova - Manual (Page 2)

FIXTURE SUPPLY
WIRE
SHAKE PROOF WASHER A
LOCK NUT A
NIPPLE
LOCK NUT B
SHAKE PROOF WASHER B
CANOPY CHAIN LOOP
COUPLING
FIXTURE CHAIN
CANOPY LOCK
RING
FIGURE 2
HOUSE SUPPLY
and GROUND
WIRES HOLE DRILLED
INSIDE OUTLET
BOX
OUTLET BOX
1. Before installing fixture, carefully unpack and identify all
parts referring to illustration FIGURE . Be sure the power
to the installation point is OFF
.
2.
3. With the NIPPLE properly situated, locate COUPLING and
proceed to thread onto the end of the NIPPLE protruding
into the OUTLET BOX. Thread COUPLING onto pipe until
tight. Tighten the top SET SCREW with pliers to secure
COUPLING to NIPPLE.
4.
Proceed to unravel
the FIXTURE SUPPLY and GROUND WIRES. Locate the
FIXTURE CHAIN and attach one end to the FIXTURE LOOP
at the top of FIXTURE. Please note that depending on chain
material thickness, you might be required to use chain pliers to
spread chain links open. Proceed to pass the FIXTURE
SUPPLY and GROUND WIRES through the chain, alternating
links. Proceed the pass the wires through the following
mounting components in this order: 1) CANOPY LOCK RING
2) LOWER CEILING CANOPY; 3)UPPER CEILING CANOPY;
4) CANOPY CHAIN LOOP; 5) SHAKE PROOF WASHER B
and LOCKNUT B; 6) NIPPLE; 7) LOCK NUT A and SHAKE
PROOF WASHER A
Note Thread LOCK NUT A and B
approx ½ at each end of NIPPLE Position the fixture over
the OUTLET BOX and pass the fixture wires through the bottom
center of the COUPLING. Pull wires through the wire way hole
on side of COUPLING. Proceed to thread the NIPPLE into the
bottom center of the COUPLING until tight. Tighten the LOWER
SET SCREW. Proceed to thread LOCK NUT A and SHAKE
PROOF WASHER A up NIPPLE until seated against the bottom
of the COUPLING. Tighten until snug with pliers. Using wire
connector (not supplied) connect the HOUSE GROUND WIRE
to the FIXTURE GROUND WIRE; connect the HOUSE WHITE
WIRE to the FIXTURE SUPPLY WIRE (WHITE or RIBBED
SIDE); connect the HOUSE BLACK (or RED) WIRE to the
FIXTURE SUPPLY WIRE (BLACK or SMOOTH SIDE). Wrap
each connection with approved electrical tape.
5. With the proper connections made, p
Proceed to attach the top of the FIXTURE CHAIN to the
bottom of the CANOPY CHAIN LOOP. Proceed to thread
LOCK NUT B and SHAKE PROOF WASHER B down onto the
top of the CANOPY CHAIN LOOP. Tighten and snug with pliers.
6. Proceed to push the LOWER CEILING CANOPY with UPPER
CEILING CANOPY upward over the OUTLET BOX. Be sure
that all wires are carefully tucked into the OUTLET BOX cavity.
Secure canopies against ceiling by threading CANOPY LOCK
RING onto the CANOPY LOOP. Tighten until snug.
(Quoizel recommends (2)
people for the rest of this installation)
Making the connections:
2
at circuit breaker
e
e
roceed to thread the
CANOPY CHAIN LOOP onto the bottom of the NIPPLE.
7. Refer back to Page 1, Step 9 and finish installation.
(Refer to Figure 3, page 3) This weight of this fixture will
require a means of support independent of the OUTLET
BOX. This fixture must b supported by 3/8-18 NPSM
NIPPLE(supplied) Th NIPPLE should be positioned so
that 3/4“ protrudes into the OUTLET BOX cavity.
.
,
.
.
. :
" .
Note: the
opposite end of the NIPPLE must be attached to a
structural or bridging member of sufficient strength to
support the fixture weight. A COTTER PIN has been
included and should be installed into the top of NIPPLE,
above HEX NUT for added safety. A clearance hole must
be drilled on the inside top center of the OUTLET BOX
Please refer to FIGURE 3
Page 3 for detailed
illustration We recommend the consultation of a
licensed electrician or contractor due to the complexity
of this installation
SET SCREWS
3/8-18 NIPPLE, SHAKE
PROOF WASHER AND
HEX NUT (INCLUDED)
IS GE5006
Page 2 of 3
01 06 -
.
COTTER
PIN
UPPER CEILING
CANOPY
LOWER CEILING
CANOPY
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
, .
. .
INSTALLATION INSTRUCTIONS:
(FOR FIXTURES OVER 25 LBS. (Canada Only)
Quoizel recommends a licensed electrician or contractor be
consulted for this installation.
Please use the information outlined in this sheet for the
ceiling installation part of your fixture assembly.